Improving power conversion efficiency (PCE) is important for broadening the applications of organic photovoltaic (OPV) cells. Here, a maximum PCE of 19.0% (certified value of 18.7%) is achieved in single‐junction OPV cells by combining material design with a ternary blending strategy. An active layer comprising a new wide‐bandgap polymer donor named PBQx‐TF and a new low‐bandgap non‐fullerene acceptor (NFA) named eC9‐2Cl is rationally designed. With optimized light utilization, the resulting binary cell exhibits a good PCE of 17.7%. An NFA F‐BTA3 is then added to the active layer as a third component to simultaneously improve the photovoltaic parameters. The improved light unitization, cascaded energy level alignment, and enhanced intermolecular packing result in open‐circuit voltage of 0.879 V, short‐circuit current density of 26.7 mA cm−2, and fill factor of 0.809. This study demonstrates that further improvement of PCEs of high‐performance OPV cells requires fine tuning of the electronic structures and morphologies of the active layers.

Although significant improvements have been achieved for organic photovoltaic cells (OPVs), the top-performing devices still show power conversion efficiencies far behind those of commercialized solar cells. One of the main reasons is the large driving force required for separating electron−hole pairs. Here, we demonstrate an efficiency of 14.7% in the single-junction OPV by using a new polymer donor PTO2 and a nonfullerene acceptor IT-4F. The device possesses an efficient charge generation at a low driving force. Ultrafast transient absorption measurements probe the formation of loosely bound charge pairs with extended lifetime that impedes the recombination of charge carriers in the blend. The theoretical studies reveal that the molecular electrostatic potential (ESP) between PTO2 and IT-4F is large, and the induced intermolecular electric field may assist the charge generation. The results suggest OPVs have the potential for further improvement by judicious modulation of ESP.

Despite more potential in realizing higher photovoltaic performance, the highest power conversion efficiency (PCE) of tandem organic photovoltaic (OPV) cells still lags behind that of state‐of‐the‐art single‐junction cells. In this work, highly efficient double‐junction tandem OPV cells are fabricated by optimizing the photoactive layers with low voltage losses and developing an effective method to tune optical field distribution. The tandem OPV cells studied are structured as indium tin oxide (ITO)/ZnO/bottom photoactive layer/interconnecting layer (ICL)/top photoactive layer/MoOx/Ag, where the bottom and top photoactive layers are based on blends of PBDB‐TF:ITCC and PBDB‐TF:BTP‐eC11, respectively, and ICL refers to interconnecting layer structured as MoOx/Ag/ZnO:PFN‐Br. As these results indicate that there is not much room for optimizing the bottom photoactive layer, more effort is put into fine‐tuning the top photoactive layer. By rationally modulating the composition and thickness of PBDB‐TF:BTP‐eC11 blend films, the 300 nm‐thick PBDB‐TF:BTP‐eC11 film with 1:2 D/A ratio is found to be an ideal photoactive layer for the top sub‐cell in terms of photovoltaic characteristics and light distribution control. For the optimized tandem cell, a PCE of 19.64% is realized, which is the highest result in the OPV field and certified as 19.50% by the National Institute of Metrology.

The development of polymerized small‐molecule acceptors has boosted the power conversion efficiencies (PCEs) of all‐polymer organic photovoltaic (OPV) cells to 17%. However, the polymer donors suitable for all‐polymer OPV cells are still lacking, restricting the further improvement of their PCEs. Herein, a new polymer donor named PQM‐Cl is designed and its photovoltaic performance is explored. The negative electrostatic potential and low average local ionization energy distribution of the PQM‐Cl surface enable efficient charge generation and transfer process. When blending with a well‐used polymer acceptor, PY‐IT, the PQM‐Cl‐based devices deliver an impressive PCE of 18.0% with a superior fill factor of 80.7%, both of which are the highest values for all‐polymer OPV cells. The relevant measurements demonstrate that PQM‐Cl‐based films possess excellent mechanical and flexible properties. As such, PQM‐Cl‐based flexible photovoltaic cells are fabricated and an excellent PCE of 16.5% with high mechanical stability is displayed. These results demonstrate that PQM‐Cl is a potential candidate for all‐polymer OPV cells and provide insights into the design of polymer donors for high‐efficient all‐polymer OPV cells.

Decreasing the energy loss is one of the most feasible ways to improve the efficiencies of organic photovoltaic (OPV) cells. Recent studies have suggested that non‐radiative energy loss (Enon-radloss ) is the dominant factor that hinders further improvements in state‐of‐the‐art OPV cells. However, there is no rational molecular design strategy for OPV materials with suppressed Enon-radloss . Herein, taking molecular surface electrostatic potential (ESP) as a quantitative parameter, we establish a general relationship between chemical structure and intermolecular interactions. The results reveal that increasing the ESP difference between donor and acceptor will enhance the intermolecular interaction. In the OPV cells, the enhanced intermolecular interaction will increase the charge‐transfer (CT) state ratio in its hybridization with the local exciton state to facilitate charge generation, but simultaneously result in a larger Enon-radloss . These results suggest that finely tuning the ESP of OPV materials is a feasible method to further improve the efficiencies of OPV cells.

By constructing a ternary cell with a B1:BO-2Cl:BO-4Cl donor:acceptors combination, an outstanding power conversion efficiency (PCE) of 17.0% (certified to be 16.9%) has been realized for all-small-molecule organic solar cells (ASM-OSCs).

The donor:acceptor heterojunction has proved as the most successful approach to split strongly bound excitons in organic solar cells (OSCs). Establishing an ideal architecture with selective carrier transport and suppressed recombination is of great importance to improve the photovoltaic efficiency while remains a challenge. Herein, via tailoring a hybrid planar/bulk structure, highly efficient OSCs with reduced energy losses (Elosss) are fabricated. A p‐type benzodithiophene‐thiophene alternating polymer and an n‐type naphthalene imide are inserted on both sides of a mixed donor:acceptor active layer to construct the hybrid heterojunction, respectively. The tailored structure with the donor near the anode and the acceptor near the cathode is beneficial for obtaining enhanced charge transport, extraction, and suppressed charge recombination. As a result, the photovoltaic characterizations suggest a reduced nonradiative Eloss by 25 meV, and the best OSC records a high efficiency of 18.5% (certified as 18.2%). This study highlights that precisely regulating the structure of donor:acceptor heterojunction has the potential to further improve the efficiencies of OSCs.

Background Osteoarthritis (OA) is the common chronic degenerative joint bone disease that is mainly featured by joint stiffness and cartilage degradation. Icariin (ICA), an extract from Epimedium, has been preliminarily proven to show anti-osteoporotic and anti-inflammatory effects in OA. However, the underlying mechanisms of ICA on chondrocytes need to be elucidated. Methods LPS-treated chondrocytes and monosodium iodoacetate (MIA)-treated Wistar rats were used as models of OA in vitro and in vivo, respectively. LDH and MTT assays were performed to detect cytotoxicity and cell viability. The expression levels of NLRP3, IL-1β, IL-18, MMP-1, MMP-13, and collagen II were detected by qRT-PCR and Western blotting. The release levels of IL-1β and IL-18 were detected by ELISA assay. Caspase-1 activity was assessed by flow cytometry. Immunofluorescence and immunohistochemistry were used to examine the level of NLRP3 in chondrocytes and rat cartilage, respectively. The progression of OA was monitored with hematoxylin-eosin (H&E) staining and safranin O/fast green staining. Results ICA could suppress LPS-induced inflammation and reduction of collagen formation in chondrocytes. Furthermore, ICA could inhibit NLRP3 inflammasome-mediated caspase-1 signaling pathway to alleviate pyroptosis induced by LPS. Overexpression of NLRP3 reversed the above changes caused by ICA. It was further confirmed in the rat OA model that ICA alleviated OA by inhibiting NLRP3-mediated pyroptosis. Conclusion ICA inhibited OA via repressing NLRP3/caspase-1 signaling-mediated pyroptosis in models of OA in vitro and in vivo, suggesting that ICA might be a promising compound in the treatment of OA.