No abstract

No abstract

Scientific interpretation of the mechanism of land use change is important for government planning and management activities. This study analyzes the land use change in Jiangsu Province using three land use maps of 2000, 2005 and 2008. The study results show that there was a significant change in land use. The change was mainly characterized by a continuous built-up land expansion primarily at the expense of cropland loss, and the trend became increasingly rapid. There was an obvious regional difference, as most of the cropland loss or built-up land expansion took place in southern Jiangsu, where the rate of built-up land expansion was faster than in central and northern Jiangsu. Meanwhile, the spatial pattern changed remarkably; in general, the number of patches (NumP) showed a declining trend, and the mean patch size (MPS) and patch size standard deviation (PSSD) displayed increase trends. Furthermore, the relative importance of selected driven factors was identified by principal component analysis (PCA) and general linear model (GLM). The results showed that not only the relative importance of a specific driving factor may vary, but the driven factors may as well. The most important driven factor changed from urban population (UP), secondary gross domestic product (SGDP) and gross domestic product (GDP) during 2000–2005 to resident population (RP), population density (POD) and UP during 2005–2008, and the deviance explained (DE) decreased from 91.60% to 81.04%. Policies also had significant impacts on land use change, which can be divided into direct and indirect impacts. Development policies usually had indirect impacts, particularly economic development policies, which promote the economic development to cause land use change, while land management policies had direct impacts. We suggest that the government should think comprehensively and cautiously when proposing a new development strategy or plan.

No abstract

No abstract

China is a disaster prone country, and a comprehensive understanding of change of disasters is very important for China's agricultural development. In this study, statistical techniques and geographic information system tools are employed to quantify the main agriculture disasters changes and effects on grain production in China during the period of 1990-2011. The results show that China's grain production was severely affected by disasters including drought, flood, hail, frost and typhoon. The annual area covered by these disasters reached up to 48.7×10 6 ha during the study period, which accounted for 44.8% of the total sown area, and about 55.1% of the per unit area grain yield change was caused by disasters. In addition, all of the disasters showed high variability, different changing trends, and spatial distribution. Drought, flood, and hail showed significantly decreasing trends, while frost and typhoon showed increasing trends. Drought and flood showed gradual changes and were distributed across the country, and disasters became more diversified from north to south. Drought was the dominated disaster type in northern China, while flood was the most important disaster type in the southern part. Hail was mainly observed in central and northern China, and frost was mainly distributed in southern China. Typhoon was greatly limited to the southeast coast. Furthermore, the resilience of grain production of each province was quite different, especially in several major grain producing areas, such as Shandong, Liaoning, Jilin and Jiangsu, where grain production was seriously affected by disasters. One reason for the difference of resilience of grain production was that grain production was marginalized in developed provinces when the economy underwent rapid development. For China's agricultural development and grain security, we suggest that governments should place more emphasis on grain production, and invest more money in disaster prevention and mitigation, especially in the major grain producing provinces.

No abstract

Wool keratin/poly(vinyl alcohol) (PVA) blend nanofibers were fabricated using the electrospinning method in formic acid solutions with different weight ratios of keratin to PVA. The resultant blend nanofibers were characterized by scanning electron microscopy (SEM), Fourier transform infrared (FTIR), X-ray diffraction (XRD), thermal gravimetric analysis (TGA), and tensile test. SEM images showed that the diameter of the blend nanofibers was affected by the content of keratin in blend solution. FTIR and XRD analyses data demonstrated that there were good interactions between keratin and PVA in the blended nanofibers caused by possibly hydrogen bonds. The TGA study revealed that the thermal stability of the blend nanofibers was between those of keratin and PVA. Tensile test indicated that the addition of PVA was able to improve the mechanical properties of the electrospun nanofibers.