ABSTRACT:We have investigated the photocatalysis of partially deuterated methanol (CD 3 OH) and H 2 O on TiO 2 (110) at 400 nm using a newly developed photocatalysis apparatus in combination with theoretical calculations. Photocatalyzed products, CD 2 O on Ti 5c sites, and H and D atoms on bridge-bonded oxygen (BBO) sites from CD 3 OH have been clearly detected, while no evidence of H 2 O photocatalysis was found. The experimental results show that dissociation of CD 3 OH on TiO 2 (110) occurs in a stepwise manner in which the O−H dissociation proceeds first and is then followed by C−D dissociation. Theoretical calculations indicate that the high reverse barrier to C−D recombination and the facile desorption of CD 2 O make photocatalytic methanol dissociation on TiO 2 (110) proceed efficiently. Theoretical results also reveal that the reverse reactions, i.e, O−H recombination after H 2 O photocatalytic dissociation on TiO 2 (110), may occur easily, thus inhibiting efficient photocatalytic water splitting. ■ INTRODUCTIONTitanium dioxide has been extensively investigated as a catalyst or photocatalyst, 1−11 particularly in applications involving photodegradation of organic molecules and water splitting, 5,12,13 which have important implications in environmental remediation and clean energy. Pure TiO 2 is apparently not photocatalytically active for splitting water to produce hydrogen, 14 but the addition of methanol to water can dramatically enhance the photocatalytic activity for hydrogen production. 15 Therefore, understanding the key differences between the photocatalytic chemistry of methanol and water on a model TiO 2 surface at the molecular level may provide valuable insight into the dynamics of photocatalysis that would enhance efforts for developing new and efficient photocatalysts for water splitting.Theoretical and experimental studies often focus on TiO 2 (110) as a model surface, 6,16 with the methanol/ TiO 2 (110) system serving as a model for photocatalysis on TiO 2 . 17−20 Henderson and co-workers 18 conducted a temperature-programmed desorption (TPD) study of CH 3 OH on TiO 2 (110) and concluded that the majority of the CH 3 OH molecules are adsorbed in molecular form. This conclusion is consistent with a scanning tunneling microscopy study by Dohnalek et al. 10 that showed that methanol molecules are adsorbed molecularly on the Ti 5c sites and are dissociated only at bridge-bonded oxygen (BBO) vacancy sites. The photocatalysis of CH 3 OH on TiO 2 (110) was investigated in a twophoton photoemission (2PPE) experiment, which inferred the presence of an excited electronic state on the surface. 20,21 Zhou et al. attributed this surface state to a photocatalytic dissociated state of methanol using a time-dependent 2PPE (TD-2PPE) technique. 22 They also used a combination of photoexcitation with STM and found that 400 nm light could induce dissociation of methanol on the surface, and they assigned the dissociated state as methoxy (CH 3 O) on a Ti 5c site and a hydrogen atom on a BBO site. Shen and Hend...

Clean hydrogen production is highly desirable for future energy needs, making the understanding of molecular-level phenomena underlying photocatalytic hydrogen production both fundamentally and practically important. Water splitting on pure TiO 2 is inefficient, however, adding sacrificial methanol could significantly enhance the photocatalyzed H 2 production. Therefore, understanding the photochemistry of methanol on TiO 2 at the molecular level could provide important insights to its photocatalytic activity. Here, we report the first clear evidence of photocatalyzed splitting of methanol on TiO 2 derived from time-dependent two-photon photoemission (TD-2PPE) results in combination with scanning tunneling microscopy (STM). STM tip induced molecular manipulation before and after UV light irradiation clearly reveals photocatalytic bond cleavage, which occurs only at Ti 4+ surface sites. TD-2PPE reveals that the kinetics of methanol photodissociation is clearly not of single exponential, an important characteristic of this intrinsically heterogeneous photoreaction.

Thermally stable Au single-atoms supported by monolayered CuO grown at Cu(110) have been successfully prepared. The charge transfer from the CuO support to single Au atoms is confirmed to play a key role in tuning the activity for CO oxidation. Initially, the negatively charged Au single-atom is active for CO oxidation with its adjacent lattice O atom depleted to generate an O vacancy in the CuO monolayer. Afterward, the Au single-atom is neutralized, preventing further CO reaction. The produced O vacancy can be healed by exposure to O at 400 K and accordingly the reaction activity is restored.

In reduced TiO2, electronic transitions originating from the Ti(3+)-induced states in the band gap are known to contribute to the photoabsorption, being in fact responsible for the material's blue color, but the excited states accessed by these transitions have not been characterized in detail. In this work we investigate the excited state electronic structure of the prototypical rutile TiO2(110) surface using two-photon photoemission spectroscopy (2PPE) and density functional theory (DFT) calculations. Using 2PPE, an excited resonant state derived from Ti(3+) species is identified at 2.5 ± 0.2 eV above the Fermi level (EF) on both the reduced and hydroxylated surfaces. DFT calculations reveal that this excited state is closely related to the gap state at ∼1.0 eV below EF, as they both result from the Jahn-Teller induced splitting of the 3d orbitals of Ti(3+) ions in reduced TiO2. Localized excitation of Ti(3+) ions via 3d → 3d transitions from the gap state to this empty resonant state significantly increases the TiO2 photoabsorption and extends the absorbance to the visible region, consistent with the observed enhancement of the visible light induced photocatalytic activity of TiO2 through Ti(3+) self-doping. Our work reveals the physical origin of the Ti(3+) related photoabsorption and visible light photocatalytic activity in prototypical TiO2 and also paves the way for the investigation of the electronic structure and photoabsorption of other metal oxides.

Although it has been widely accepted that the crystal phase, morphology, and facet significantly influence the catalytic and photocatalytic activity of TiO2, establishing the correlation between structure and activity of heterogeneous reactions is very difficult because of the complexity of the structure. Utilizing ultrahigh vacuum (UHV) based temperature-programmed desorption (TPD) and density functional theory (DFT) calculations, we have successfully assessed the photoreactivity of two well characterized rutile surfaces ((011)-(2×1) and (110)-(1×1)) through examining the photocatalyzed oxidation of methanol. The photocatalytic products, such as formaldehyde and methyl formate, are the same on both surfaces under UV illumination. However, the reaction rate on (011)-(2×1) is only 42% of that on (110)-(1×1), which contradicts previous reports in aqueous environments where characterization of TiO2 structure is difficult. The discrepancy probably comes from the differences of the TiO2 structure in these studies. Our DFT calculations reveal that the rate-determining step of methanol dissociation on both surfaces is C–H scission,; however, the barrier of this elementary step on (011)-(2×1) is about 0.2 eV higher than that on (110)-(1×1) because of their distinct surface atomic configurations. The present work not only demonstrates the importance of surface structure in the photoreactivity of TiO2, but also provides an example for building the correlation between structure and activity using surface science techniques and DFT calculations.