Micro-turbomachinery demands gas bearings to ensure compactness, light weight, and extreme temperature operation. Gas bearings with large stiffness and damping, and preferably of low cost, will enable successful commercial applications. Presently, tests conducted on a small rotor supported on flexure pivot hydrostatic pad gas bearings (FPTPBs) demonstrate stable rotordynamic responses up to 100,000rpm (limit of the drive motor). Test rotor responses show the feed pressure raises the system critical speed (increase in bearing direct stiffness) while the viscous damping ratio decreases. Predictions correlate favorably with experimentally identified (synchronous) direct stiffness bearing force coefficients. Identified experimental gas bearing synchronous damping coefficients are 50% or less of the predicted magnitudes, though remaining relatively constant as the rotor speed increases. Tests without feed pressure show the rotor becomes unstable at ∼81krpm with a whirl frequency ratio of 20%. FPTPBs are mechanically complex and more expensive than cylindrical plain bearings. However, their enhanced stability characteristics and predictable rotordynamic performance makes them desirable for the envisioned oil-free applications in high speed micro-turbomachinery.
Reliable gas bearings will enable the rapid deployment of high speed oil-free micro-turbomachinery. This paper presents analysis and experiments of the dynamic performance of a small rotor supported on Rayleigh step gas bearings. Comprehensive tests demonstrate that Rayleigh step hybrid gas bearings exhibit adequate stiffness and damping capability in a narrow range of shaft speeds, up to ∼ 20 krpm. Rotor coast down responses were performed with two test bearing sets with nominal radial clearance of 25 μm and 38 μm. A near-frictionless carbon (NFC) coating was applied on the rotor to reduce friction at liftoff and touchdown. However, the rotor could not lift easily and severe rubbing occurred at shaft speeds below ∼ 4,000 rpm. The tests show that the supply pressure raises the rotor critical speed and decreases the system damping ratio, while only affecting slightly the rotor-bearing system onset speed of instability. Whirl frequencies are nearly fixed at the system natural frequency (∼ 120 Hz) with subsynchronous amplitude motions of very large magnitude that prevented rotor operation above ∼ 20 krpm. The geometry of the Rayleigh steps distributed on the rotor surface generates a time varying pressure field, resulting in a sizable 4X super synchronous component of bearing transmitted load. Predictions show the synchronous stiffness and damping coefficients decrease with shaft speed. Predicted threshold speeds of instability are much lower than measured values due to the analytical model limitations assuming a grooved stator. The predicted synchronous responses to imbalance correlate well with the measurements. The Rayleigh step gas bearings are the most unreliable rigid bearing configuration tested to date.
Micro-turbomachinery demands gas bearings to ensure compactness, lightweight and extreme temperature operation. Gas bearings with large stiffness and damping, and preferably of low cost, will enable successful commercial applications. Presently, tests conducted on a small rotor supported on flexure pivot–hydrostatic pad gas bearings (FPTPBs) demonstrate stable rotordynamic responses up to 100,000 rpm (limit of the drive motor). Test rotor responses show the feed pressure raises the system critical speed (increase in bearing direct stiffness) while the viscous damping ratio decreases. Predictions correlate favorably with experimentally identified (synchronous) direct stiffness bearing force coefficients. Identified experimental gas bearing synchronous damping coefficients are 50% or less of the predicted magnitudes, though remaining relatively constant as the rotor speed increases. Tests without feed pressure show the rotor becomes unstable at ∼ 81 krpm with a whirl frequency ratio of 20%. FPTPBs are mechanically complex and more expensive than cylindrical plain bearings. However, their enhanced stability characteristics and predictable rotordynamic performance makes them desirable for the envisioned oil-free applications in high speed micro turbomachinery.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
customersupport@researchsolutions.com
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.