A new adsorbent Srp/HAP for simultaneous removal of fluoride, iron and manganese was prepared, characterized and analyzed.
Insoluble humic acid/tourmaline composite particles (IHA/TM) were prepared by combining inorganic tourmaline (TM) with the natural organic polymer humic acid (HA) and carbonizing them at 330 °C to study the removal characteristics and mechanism of Fe2+ and Mn2+. The results showed that the optimal ratio of TM to IHA is 2:3. When the temperature of the IHA/TM composite particles was 35 °C and the pH was 6, the adsorption of Fe2+ and Mn2+ by IHA/TM reached equilibrium at 240 min. The optimum dose of the adsorbent was 10 g/L, and the equilibrium adsorption capacities of Fe2+ and Mn2+ were 5.645 mg/g and 3.574 mg/g, respectively. The process of IHA/TM adsorption of Fe2+ and Mn2+ in water was spontaneous, endothermic and sustainable, and cooling was not conducive to adsorption. The pseudo-second order kinetic equation can well reflect the adsorption mechanism of IHA/TM on Fe2+ and Mn2+, and the Langmuir adsorption model better describes the isothermal adsorption behaviour. The material characterisation and adsorption experiments indicate that surface coordination and chemical precipitation are the main mechanisms of Fe2+ and Mn2+ removal by IHA/TM.
Iron- and manganese-contaminated mine water is widespread around the world, and economical and efficient remediation has become a priority. Insoluble humic acid/tourmaline composite particles (IHA/TM) were prepared by combining inorganic tourmaline (TM) with the natural organic polymer humic acid (HA), and the effects of different calcination temperatures and calcination times of TM and IHA on the adsorption of Fe2+ and Mn2+ were analyzed. Based on the microscopic characterization of Scanning electron microscopy (SEM), Energy Dispersive Spectroscopy (EDS), Brunnauer–Emmet–Teller (BET), X-ray diffractometer (XRD) and Fourier transform infrared (FTIR), the simultaneous adsorption performance of IHA/TM on Fe2+ and Mn2+ was studied through dynamic adsorption tests, and a dynamic adsorption model was established. Adsorption regeneration experiments were carried out to further investigate the effectiveness of the composite particles in practical applications. The results show that, when the calcination temperature was 330 °C and the calcination time was 90 min, the removal rates of iron and manganese by the IHA/TM composite particles reached 99.85% and 99.51%, respectively. The curves for penetration of Fe2+ and Mn2+ ions into the IHA/TM composite particles were affected by the bed height, flow rate and influent concentration. Decreasing the flow rate, decreasing the influent concentration, or increasing the bed height prolonged the operation time of the dynamic column. If the bed height was too low, the penetration point was reached before the expected treatment was achieved, and when the bed height was too high, the removal of Fe2+ and Mn2+ was slow, and the utilization rate of the adsorbent was also reduced. If the flow rate was too low, longitudinal remixing easily occurred in the column. However, when the flow rate was too high, the speed of Fe2+ and Mn2+ ions passing through the adsorption layer increased, which reduced the total amount of adsorption. The increase in influent concentration not only reduces the removal rate, but also greatly shortens the total operation time of the dynamic column and reduces the treatment water. The dynamic process for the adsorption of Fe2+ and Mn2+ by IHA/TM was fitted best by the Thomas model. The adsorption column was continuously regenerated five times, and the results show that the IHA/TM composite particles were suitable for iron and manganese removal from mine wastewater. The research results will provide a reference for the effectiveness of the IHA/TM composite particles in practical applications.
Using calcium polysulfide as the reducing agent, synthetic zeolite as the adsorbent, and cement as the curing agent, the dual-index orthogonal test method was used to determine the best remediation dosage of chromium-contaminated soil. On this basis, through the dry–wet cycle test, the durability of the chromium-contaminated soil after repair is analyzed from the perspectives of unconfined compressive strength, toxic leaching concentration, quality loss, and microscopic characterization. Test results showed that the optimal ratio for the joint repair of chromium-contaminated soil was 3 times the amount of CaS5, 15% synthetic zeolite, and 20% cement. With the increase in the number of wet–dry cycles, the unconfined compressive strength of the composite preparation combined to repair chromium-contaminated soil was first increased and then reduced, and the concentration of Cr(VI) and total chromium in the leachate was first decreased and then increased. The higher the chromium content of the contaminated soil was, the lower the unconfined compressive strength, and the higher the leaching concentration of Cr(VI) and total chromium were. With the increase in cycle times, the cumulative mass-loss rate of composite preparations for repairing chromium-contaminated soil gradually increased, and the higher the chromium content was, the higher the cumulative mass-loss rate, which was less than 2%, reflecting the combination of composite preparations for repairing chromium-contaminated soil to have good durability. Microscopic and macroscopic results are consistent with each other.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.