Recently, decellularized extracellular matrix-based bio-ink (dECM bio-ink) derived from animal organs is attracting attention because of its excellent biocompatibility. However, its poor 3D printability and weak mechanical properties remain a challenge. Here, we developed a new dECM bio-ink with enhanced 3D printability and mechanical properties. dECM micro-particles of about 13.4 μm in size were prepared by decellularizing a porcine liver followed by freeze-milling. The new bio-ink, named as dECM powder-based bio-ink (dECM pBio-ink), was prepared by loading the dECM micro-particles into a gelatin mixture. The usefulness of the dECM pBio-ink was evaluated by assessing its mechanical properties, printability, and cytocompatibility. The results showed that its mechanical properties and 3D printability were greatly improved. Its elastic modulus increased by up to 9.17 times that of the conventional dECM bio-ink. Micro-patterns with living cells were successfully achieved with 93% cell viability. Above all, the new bio-ink showed superior performance in stacking of layers for 3D printing, whereas the conventional bio-ink could not maintain its shape. Finally, we demonstrated that the dECM pBio-ink possessed comparable cytocompatibility with the conventional dECM bio-ink through in vitro tests with endothelial cells and primary mouse hepatocytes.
The formation of a dense zwitterionic brush through surface-initiated atom transfer radical polymerization (SI-ATRP) is a typical graft-from approach used to achieve antifouling surfaces with high fidelity; however, their air-tightness may cause inconvenience to users. In this context, activator regenerated by electron transfer (ARGET) ATRP is emerging as an alternative surface-coating tool because limited amount of air is allowed to form a dense polymer brush. However, the degree of air tolerance that can ensure a thick polymer brush has not been clearly defined, limiting its practical usage under ambient-air conditions. In this study, we investigated the SI-ARGET ATRP of carboxybetaine (CB) by changing the air conditions, along with the air-related parameters, such as the concentration of the reducing agent, the volume of the polymerization solution (PS), or the solvent composition, and correlated their effects with the poly(CB) thickness. Based on the optimized reaction conditions, a poly(CB) brush with reliable thickness was feasibly formed even under open-air conditions without a degassing step. In addition, a microliter droplet (∼100 μL) of PS was sufficient to proceed with the SI-ARGET ATRP for the covering of a poly(CB) brush on the surface area of interest. By applying an optimized SI-ARGET ATRP of CB, antifouling was feasibly achieved in the surface region of interest using an array to form a large surface area under fully exposed air conditions. In other words, optimized SI-ARGET ATRP enabled the formation of a thick poly(CB) brush on the surfaces of various dimensions under open-air conditions.
Cell-cell interaction accounts for one of the most influential factors affecting the viability and functionality of cell-based tissue models. In this respect, various methods capable of producing micro-patterns with cell spheroids are introduced to simultaneously improve contact-dependent and-independent cell-cell interactions. However, no method has yet been designed to effectively generate precise 3D patterns with multiple spheroid types. In this study, a new high-precision and convenient 3D spheroid printing technology is developed, designated as 3D bio-dot printing. This new technique is designed to produce cell-laden, non-adhesive micro-pores within 3D structures to allow cell spheroids to be induced at printed sites. Experimental results show that various cell types, including hepatocytes, pancreatic β-cells, and breast cancer cells, can be employed for the in situ formation of cell spheroids, and 3D freeform structures with multiple spheroid types can be printed. Moreover, this novel technology can also be used for performing 3D invasion assays. More importantly, it ensures that the precise control of spheroid size and position is achieved at micrometer scale. Finally, the usefulness of this novel technology is demonstrated by producing multicellular micro-patterns with primary hepatocyte spheroids and endothelial cells, that exhibit significantly improved long-term hepatic function and drug metabolism.
Decellularized extracellular matrix-based bio-inks (dECM bio-inks) for bioprinting technology have recently gained attention owing to their excellent ability to confer tissue-specific functions and 3D-printing capability. Although decellularization has led to a major advancement in bio-ink development, the effects of detergent type, the most important factor in decellularization, are still unclear. In this study, the effects of various detergent types on bio-ink performance were investigated. Porcine liver-derived dECM bio-inks prepared using widely used detergents, including sodium dodecyl sulfate (SDS), sodium deoxycholate (SDC), Triton X-100 (TX), and TX with ammonium hydroxide (TXA), were characterized in detail. SDS and SDC severely damaged glycosaminoglycan and elastin proteins, TX showed the lowest rate of decellularization, and TXA-based dECM bio-ink possessed the highest ECM content among all bio-inks. Differences in biochemical composition directly affected bio-ink performance, with TXA-dECM bio-ink showing the best performance with respect to gelation kinetics, intermolecular bonding, mechanical properties, and 2D/3D printability. More importantly, cytocompatibility tests using primary mouse hepatocytes also showed that the TXA-dECM bio-ink improved albumin secretion and cytochrome P450 activity by approximately 2.12- and 1.67-fold, respectively, compared with the observed values for other bio-inks. Our results indicate that the detergent type has a great influence on dECM damage and that the higher the dECM content, the better the performance of the bio-ink for 3D bioprinting.
In this study, we developed a uniform initiator layer that can be formed on various surfaces, and formed site-selectively, for the subsequent antifouling polymer brush formation. Initially, metal–organic films composed of tannic acid (TA) and FeIII ions (TA-FeIII) were formed on various surfaces, followed by functionalization with an aryl azide-based initiator (ABI) under photoreaction. In particular, combination with a photolithographic technique enabled the presentation of initiators only on the intended region within a single-surface platform. A resultant initiator film (TF-ABI) was formed under mild reaction conditions and meets the uniformity and transparency requirements concurrently. Subsequently, we showed that TF-ABI can be further utilized to form a polymer brush by proceeding with surface-initiated polymerization using a zwitterionic monomer, namely, sulfobetaine acrylamide (SBAA). Instead of applying a classical, yet air-sensitive atom transfer radical polymerization (ATRP) technique, we utilized an activator regenerated by electron transfer (ARGET) ATRP under air conditions without a cumbersome deoxygenation step. Overall, our initiator layer allowed the antifouling poly(SBAA) brush to be used on various surfaces, and enabled their pattern generation.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.