Voltage decay and redox asymmetry mitigation by reversible cation migration in lithiumrich layered oxide electrodes.

Fabricating inorganic–organic hybrid perovskite solar cells (PSCs) on plastic substrates broadens their scope for implementation in real systems by imparting portability, conformability and allowing high-throughput production, which is necessary for lowering costs. Here we report a new route to prepare highly dispersed Zn2SnO4 (ZSO) nanoparticles at low-temperature (<100 °C) for the development of high-performance flexible PSCs. The introduction of the ZSO film significantly improves transmittance of flexible polyethylene naphthalate/indium-doped tin oxide (PEN/ITO)-coated substrate from ∼75 to ∼90% over the entire range of wavelengths. The best performing flexible PSC, based on the ZSO and CH3NH3PbI3 layer, exhibits steady-state power conversion efficiency (PCE) of 14.85% under AM 1.5G 100 mW·cm−2 illumination. This renders ZSO a promising candidate as electron-conducting electrode for the highly efficient flexible PSC applications.

Co-intercalation reactions make graphite as promising anodes for sodium ion batteries, however, the high redox potentials significantly lower the energy density. Herein, we investigate the factors that influence the co-intercalation potential of graphite and find that the tuning of the voltage as large as 0.38 V is achievable by adjusting the relative stability of ternary graphite intercalation compounds and the solvent activity in electrolytes. The feasibility of graphite anode in sodium ion batteries is confirmed in conjunction with Na 1.5 VPO 4.8 F 0.7 cathodes by using the optimal electrolyte. The sodium ion battery delivers an improved voltage of 3.1 V, a high power density of 3863 W kg −1 both electrodes , negligible temperature dependency of energy/power densities and an extremely low capacity fading rate of 0.007% per cycle over 1000 cycles, which are among the best thus far reported for sodium ion full cells, making it a competitive choice in large-scale energy storage systems.

With the demand for high-energy-storage devices, the rechargeable metal–oxygen battery has attracted attention recently. Sodium–oxygen batteries have been regarded as the most promising candidates because of their lower-charge overpotential compared with that of lithium–oxygen system. However, conflicting observations with different discharge products have inhibited the understanding of precise reactions in the battery. Here we demonstrate that the competition between the electrochemical and chemical reactions in sodium–oxygen batteries leads to the dissolution and ionization of sodium superoxide, liberating superoxide anion and triggering the formation of sodium peroxide dihydrate (Na2O2·2H2O). On the formation of Na2O2·2H2O, the charge overpotential of sodium–oxygen cells significantly increases. This verification addresses the origin of conflicting discharge products and overpotentials observed in sodium–oxygen systems. Our proposed model provides guidelines to help direct the reactions in sodium–oxygen batteries to achieve high efficiency and rechargeability.

Anatase TiO2 is considered as one of the promising anodes for sodium‐ion batteries because of its large sodium storage capacities with potentially low cost. However, the precise reaction mechanisms and the interplay between surface properties and electrochemical performance are still not elucidated. Using multimethod analyses, it is herein demonstrated that the TiO2 electrode undergoes amorphization during the first sodiation and the amorphous phase exhibits pseudocapacitive sodium storage behaviors in subsequent cycles. It is also shown that the pseudocapacitive sodium storage performance is sensitive to the nature of solid electrolyte interphase (SEI) layers. For the first time, it is found that ether‐based electrolytes enable the formation of thin (≈2.5 nm) and robust SEI layers, in contrast to the thick (≈10 nm) and growing SEI from conventional carbonate‐based electrolytes. First principle calculations suggest that the higher lowest unoccupied molecular orbital energies of ether solvents/ion complexes are responsible for the difference. TiO2 electrodes in ether‐based electrolyte present an impressive capacity of 192 mAh g−1 at 0.1 A g−1 after 500 cycles, much higher than that in carbonate‐based electrolyte. This work offers the clarified picture of electrochemical sodiation mechanisms of anatase TiO2 and guides on strategies about interfacial control for high performance anodes.

No abstract

No abstract

The electrochemical properties and performances of lithium-ion batteries are primarily governed by their constituent electrode materials, whose intrinsic thermodynamic and kinetic properties are understood as the determining factor. As a part of complementing the intrinsic material properties, the strategy of nanosizing has been widely applied to electrodes to improve battery performance. It has been revealed that this not only improves the kinetics of the electrode materials but is also capable of regulating their thermodynamic properties, taking advantage of nanoscale phenomena regarding the changes in redox potential, solid-state solubility of the intercalation compounds, and reaction paths. In addition, the nanosizing of materials has recently enabled the discovery of new energy storage mechanisms, through which unexplored classes of electrodes could be introduced. Herein, we review the nanoscale phenomena discovered or exploited in lithium-ion battery chemistry thus far and discuss their potential implications, providing opportunities to further unveil uncharted electrode materials and chemistries. Finally, we discuss the limitations of the nanoscale phenomena presently employed in battery applications and suggest strategies to overcome these limitations.