No abstract

A new type of soft contact lens was developed from the poly(vinyl alcohol) (PVA) hydrogel prepared by a low temperature crystallization technique using a water-dimethyl sulfoxide mixed solvent. The PVA contact lens materials had a water content of 78% and a tensile strength of 50 kg/cm2, five times as strong as that of commercial poly(2-hydroxyethyl methacrylate) soft contact lens. The amount of proteins adsorbed to the PVA soft hydrogel material was half to one thirtieth of that of conventional soft contact lenses. Histological and scanning electron microscopic observation of rabbit eyes which had worn the PVA soft contact lens for 12 weeks showed no difference in corneal epithelium and cell arrangement in the corneal epithelium from the non-wearing eyes.

We report fabrication and characterization of microfluidic devices made of thermoplastic and elastomeric polymers. These hard-soft hybrid material devices are motivated by the combined need for large scale manufacturability, enhanced barrier properties to gas permeation and evaporation of aqueous solutions compared to poly(dimethyl siloxane) (PDMS) devices, and compatibility with deformation-based actuation. Channel features are created on rigid polymers such as polyethylene terephthalate glycol (PETG), cyclic olefin copolymer (COC), and polystyrene (PS) by hot embossing. These "hard tops" are bonded to elastomeric "soft bottoms" (polyurethane (PU) or PDMS-parylene C-PDMS) to create devices that can be used for microfluidic cell culture where deformation-based fluid actuation schemes are used to perfuse and recirculate media. The higher barrier properties of this device compared to PDMS devices enable cell culture with less evaporation and creation of hypoxic conditions.

Gel spinning of poly(vinyl alcohol) (PVA) was attempted from the PVA dope prepared from the mixture of dimethyl sulfoxide (DMSO) and water. The DMSO/H2O = 80/20 (w/w) mixture and methanol were found to be the best solvent for the spinning dope and the coagulant, respectively, to give PVA fiber with the highest drawability. PVA fiber with the highest strength and Young's modulus were obtained from the undrawn gel fibers when subjected to hot two‐stage drawing under conditions such as to produce maximum drawability. Furthermore, higher draw ratios of PVA fiber were attained at 6 wt % dope by lowering the coagulating temperature of methanol. In the present work, the highest tensile strength (2.8 GPa) and the highest Young's modulus (64 GPa) were realized, when the spinning dope was prepared from PVA with DP of 5,000 and the DMSO/H2O (80/20) mixed solvent to have the PVA concentration of 6 wt %, the coagulating temperature of methanol was −20°C, and the two‐stage drawing was carried out at 160 (first) and 200°C (second). The PVA fiber prepared under this gel spinning condition could be elongated to 45 times draw ratio. The very high drawability of PVA fibers obtained from the DMSO/H2O (80/20) mixture dope was ascribed to the ability of the DMSO/H2O mixture to promote gelation. © 1994 John Wiley & Sons, Inc.

This manuscript describes a thin amperometric nitric oxide (NO) sensor that can be microchannel embedded to enable direct real-time detection of NO produced by cells cultured within the microdevice. A key for achieving the thin (~ 1 mm) planar sensor configuration required for sensor-channel integration is the use of gold/indium-tin oxide patterned electrode directly on a porous polymer membrane (pAu/ITO) as the base working electrode. Electrochemically deposited Au-hexacyanoferrate layer on pAu/ITO is used to catalyze NO oxidation to nitrite at lower applied potentials (0.65 ~ 0.75 V vs. Ag/AgCl) and stabilize current output. Furthermore, use of a gas-permeable membrane to separate internal sensor compartments from the sample phase imparts excellent NO selectivity over common interferents (e.g., nitrite, ascorbate, ammonia, etc.) present in culture media and biological fluids. The optimized sensor design reversibly detects NO down to ~1 nM level in stirred buffer and <10 nM in flowing buffer when integrated within a polymeric microfluidic device. We demonstrate utility of the channel-embedded sensor by monitoring NO generation from macrophages cultured within non-gas permeable microchannels, as they are stimulated with endotoxin.

A novel electrochemical device for the direct detection of S-nitrosothiol species (RSNO) is proposed by modifying an amperometric nitric oxide (NO) gas sensor with thin hydrogel layer containing an immobilized organoselenium catalyst. The diselenide, 3,3'-dipropionicdiselenide, is covalently coupled to primary amine groups in polyethylenimine (PEI), which is further cross-linked to form a hydrogel layer on a dialysis membrane support. Such a polymer film containing the organoselenium moiety is capable of decomposing S-nitrosothiols to generate NO(g) at the distal tip of the NO sensor. Under optimized conditions, various RSNOs (e.g., nitrosocysteine (CysNO), nitrosoglutathione (GSNO), etc.) are reversibly detected at

The direct amperometric detection of S-nitrosothiol species (RSNOs) is realized by modifying a previously reported amperometric nitric oxide gas sensor with thin hydrophilic polyurethane films containing catalytic Cu(II)/(I) sites. Catalytic Cu(II)/(I)-mediated decomposition of S-nitrosothiols generates NO(g) in the thin polymeric film at the distal tip of the NO sensor. Three different species are examined to create the catalytic layer: (1) a lipophilic Cu(II)-ligand complex; (2) Cu(II)-phosphate salt; and (3) small (3-microm) metallic Cu(0) particles. All three catalytic layers yield reversible amperometric response in proportion to the concentration of S-nitrosothiols (e.g., nitrosocysteine, nitrosoglutathione, S-nitroso-N-acetylcysteine, S-nitrosoalbumin) present in the aqueous test solution. Sensitivity toward the different RSNO species is dependent on the respective catalytic rates of decomposition of the RSNO species by reactive Cu(I), accessibility of the species into the polyurethane layer containing the catalyst, the level of reducing agents (ascorbate) used in solution to help generate reactive Cu(I) species, and the concentration of metal ion complexing agents present in the test solution (e.g., EDTA). Under optimized conditions, all RSNO species can be detected at < or =1 microM levels, with sensor lifetimes of at least 10 days for the sensors based on Cu(II)-phosphate and Cu0 particles. It is further shown that the new RSNO sensors can be used to assess the "NO-generating" ability of fresh blood samples by effectively detecting the total level of reactive RSNO species present in such samples.

Speciation, thermodynamic stability, and structural information of aqueous oxalato-Am(iii) complexes were resolved by combinatorial use of UV-Vis-LWCC, TRLFS, and DFT calculations.