The dyes extracted from pomegranate and berry fruits were successfully used in the fabrication of natural dye sensitized solar cells (NDSSC). The morphology, porosity, surface roughness, thickness, absorption and emission characteristics of the pomegranate dye sensitized photo-anode were studied using various analytical techniques including FESEM, EDS, TEM, AFM, FTIR, Raman, Fluorescence and Absorption Spectroscopy. Pomegranate dye extract has been shown to contain anthocyanin which is an excellent light harvesting pigment needed for the generation of charge carriers for the production of electricity. The solar cell’s photovoltic performance in terms of efficiency, voltage, and current was tested with a standard illumination of air-mass 1.5 global (AM 1.5 G) having an irradiance of 100 mW/cm2. After optimization of the photo-anode and counter electrode, a photoelectric conversion efficiency (η) of 2%, an open-circuit voltage (Voc) of 0.39 mV, and a short-circuit current density (Isc) of 12.2 mA/cm2 were obtained. Impedance determination showed a relatively low charge-transfer resistance (17.44 Ω) and a long lifetime, signifying a reduction in recombination losses. The relatively enhanced efficiency is attributable in part to the use of a highly concentrated pomegranate dye, graphite counter electrode and TiCl4 treatment of the photo-anode.

The Turkevich-Frens synthesis starting conditions are expanded, ranging the gold salt concentrations up to 2 mM and citrate/gold(III) molar ratios up to 18:1. For each concentration of the initial gold salt solution, the citrate/gold(III) molar ratios are systematically varied from 2:1 to 18:1 and both the size and size distribution of the resulting gold nanoparticles are compared. This study reveals a different nanoparticle size evolution for gold salt solutions ranging below 0.8 mM compared to the case of gold salt solutions above 0.8 mM. In the case of [Au 3+ ]<0.8 mM, both the size and size distribution vary substantially with the citrate/gold(III) ratio, both displaying plateaux that evolve inversely to [Au 3+ ] at larger ratios. Conversely, for [Au 3+ ]≥0.8 mM, the size and size distribution of the synthesized gold nanoparticles continuously rise as the citrate/gold(III) ratio is increased. A starting gold salt concentration of 0.6 mM leads to the formation of the most monodisperse gold nanoparticles (polydispersity index< 0.1) for a wide range of citrate/gold(III) molar ratios (from 4:1 to 18:1). Via a model for the formation of gold nanoparticles by the citrate method, the experimental trends in size could be qualitatively predicted: the simulations showed that the destabilizing effect of increased electrolyte concentration at high initial [Au 3+ ] is compensated by a slight increase in zeta potential of gold nanoparticles to produce concentrated dispersion of gold nanoparticles of small sizes.

Lisinopril was used as the targeting moiety to prepare gold nanoparticle-based functional CT contrast agents. Pure lisinopril, thioctic acid-lisinopril conjugate, and reduced thioctic acid-lisinopril conjugate were used to obtain GNP-Lis, GNP-TA-Lis, and GNP-RTA-Lis, respectively, via ligand exchange reaction on citrate-coated gold nanoparticles (GNPs). These lisinopril-decorated GNPs were fully characterized, and their chemical stabilities in biological relevant media and in high salt concentration were compared. Their relative stabilities toward lyophilization and against cyanide-induced decomposition were also investigated. Because of their higher stability, GNP-TA-Lis were used to assess the targeting of angiotensin converting enzyme (ACE) using X-ray computed tomography (CT). The images obtained displayed high contrast in the region of the lungs and heart, clearly indicating the targeting of ACE, whose overexpression is associated with development of cardiac and pulmonary fibrosis. Thus, the new nanoprobes prepared here will serve as very useful tools for the monitoring of cardiovascular pathophysiologies using CT imaging.

No abstract

Reduced graphene oxide has certain unique qualities that make them versatile for a myriad of applications. Unlike graphene oxide, reduced graphene oxide is a conductive material and well suited for use in electrically conductive materials, such as solar cell devices. In this study, we report on the synthesis of graphene oxide as well as the fabrication and characterization of dye-sensitized solar cells with a photoanode which is an amalgam of reduced graphene oxide and titanium dioxide. The synthesized reduced graphene oxide and the corresponding photoanode were fully characterized using Ultraviolet-visible, Fourier transform infrared (FTIR), and Raman Spectrometry. The morphology of the sample was assessed using Atomic Force Microscopy, Field Emission Scanning Electron Microscopy, Transmission Electron Microscopy, and Energy Dispersive X-ray Spectroscopy. The photovoltaic characteristics were determined by photocurrent and photo-voltage measurements of the fabricated solar cells. The electrical impedances of both sets of devices were also evaluated. Overall, the solar to electric power efficiency of the device with reduced graphene oxide was observed to be higher (2.02%) than the device without the reduced graphene oxide (1.61%).

No abstract

No abstract

This research study focused on improving the methodology of producing dye-sensitized solar cells (DSSC) by the process of amalgamation with natural dyes. This research is done with the hope of maximizing cell efficiency and sustainable power production for mass manufacturing processes at the most economical cost. The construction of DSSC is a three-step process comprising: dye extraction, TiO 2 paste application, and solar cell structure. These important factors contribute significantly to the efficiency maximization of a dye-sensitized solar cell. This research work conducted specifically explored different ways of improving the current-voltage potential of the solar cells. The solar cell's performance in terms of efficiency and power output (voltage vs. current) was tested under an indoor room light, a halogen lamp and direct sunlight. The experimental results show that the dye extract from Green Cabbage produced the greatest photoelectric conversion efficiency (η) of up to 0.1%, an open-circuit voltage (V OC) of 532 mV, and a short-circuit current density (Jsc) of 1.2 mA/cm 2 .