Boron carbide displays a rich response to dynamic compression that is not well understood. To address poorly understood aspects of behavior, including dynamic strength and the possibility of phase transformations, a series of plate impact experiments was performed that also included reshock and release configurations. Hugoniot data were obtained from the elastic limit (15–18 GPa) to 70 GPa and were found to agree reasonably well with the somewhat limited data in the literature. Using the Hugoniot data, as well as the reshock and release data, the possibility of the existence of one or more phase transitions was examined. There is tantalizing evidence, but at this time no phase transition can be conclusively demonstrated. However, the experimental data are consistent with a phase transition at a shock stress of about 40 GPa, though the volume change associated with it would have to be small. The reshock and release experiments also provide estimates of the shear stress and strength in the shocked state as well as a dynamic mean stress curve for the material. The material supports only a small shear stress in the shocked (Hugoniot) state, but it can support a much larger shear stress when loaded or unloaded from the shocked state. This strength in the shocked state is initially lower than the strength at the elastic limit but increases with pressure to about the same level. Also, the dynamic mean–stress curve estimated from reshock and release differs significantly from the hydrostate constructed from low-pressure data. Finally, a spatially resolved interferometer was used to directly measure spatial variations in particle velocity during the shock event. These spatially resolved measurements are consistent with previous work and suggest a nonuniform failure mode occurring in the material.

No abstract

The shock behavior of two varieties of the ceramic silicon carbide was investigated through a series of time-resolved plate impact experiments reaching stresses of over 140 GPa. The Hugoniot data obtained are consistent for the two varieties tested as well as with most data from the literature. Through the use of reshock and release configurations, reloading and unloading responses for the material were found. Analysis of these responses provides a measure of the ceramic’s strength behavior as quantified by the shear stress and the strength in the Hugoniot state. While previous strength measurements were limited to stresses of 20–25 GPa, measurements were made to 105 GPa in the current study. The initial unloading response is found to be elastic to stresses as high as 105 GPa, the level at which a solid-to-solid phase transformation is observed. While the unloading response lies significantly below the Hugoniot, the reloading response essentially follows it. This differs significantly from previous results for B4C and Al2O3. The strength of the material increases by about 50% at stresses of 50–75 GPa before falling off somewhat as the phase transformation is approached. Thus, the strength behavior of SiC in planar impact experiments could be characterized as metal-like in character. The previously reported phase transformation at ∼105GPa was readily detected by the reshock technique, but it initially eluded detection with traditional shock experiments. This illustrates the utility of the reshock technique for identifying phase transformations. The transformation in SiC was found to occur at about 104 GPa with an associated volume change of about 9%.

No abstract

This paper describes FAST, a novel simulation methodology that can produce simulators that (i) are orders of magnitude faster than comparable simulators, (ii) are cycleaccurate, (iii) model the entire system running unmodified applications and operating systems, (iv) provide visibility with minimal simulation performance impact and (v) are capable of running current instruction sets such as x86. It achieves its capabilities by partitioning simulators into a speculative functional model component that simulates the instruction set architecture and a timing model component that predicts performance. The speculative functional model enables the simulator to be parallelized, implementing the timing model in FPGA hardware for speed and the functional model using a modified full-system simulators. We currently achieve an average simulation speed of 1.2MIPS running x86 applications on x86 Linux and Windows XP and expect to achieve 10MIPS over time. Such simulators are useful to virtually all computer system simulator users ranging from architects, through RTL designers and verifiers to software developers. Sharing a common simulation/design infrastructure could foster better communication between these groups, potentially resulting in better system designs.40th IEEE/ACM International Symposium on Microarchitecture

Pulsed power accelerators compress electrical energy in space and time to provide versatile experimental platforms for high energy density and inertial confinement fusion science. The 80-TW “Z” pulsed power facility at Sandia National Laboratories is the largest pulsed power device in the world today. Z discharges up to 22 MJ of energy stored in its capacitor banks into a current pulse that rises in 100 ns and peaks at a current as high as 30 MA in low-inductance cylindrical targets. Considerable progress has been made over the past 15 years in the use of pulsed power as a precision scientific tool. This paper reviews developments at Sandia in inertial confinement fusion, dynamic materials science, x-ray radiation science, and pulsed power engineering, with an emphasis on progress since a previous review of research on Z in Physics of Plasmas in 2005.

No abstract

No abstract