Erosi partikel pasir merupakan salah satu permasalahan yang serius dalam industri produksi minyak dan gas. Terdapat suatu bukti kuat bahwa kebanyakan sumur sekarang memproduksi pasir yang semakin meningkat seiriing penurunan produksi utama minyak dan gas. Hal ini merupakan masalah yang luas mengingat dapat mempengaruhi laju produksi seiring bertambahnya umur asset. Prediksi erosi yang akurat terutama pada elbow dapat digunakan untuk meningkatkan desain kerja pipa, wilayah inspeksi, limit pengoperasian, dan lainnya. Dalam penelitian ini digunakan permodelan CFD pada aplikasi ANSYS Student Version 19.0 untuk memprediksi erosi dalam aliran gas turbulen dengan variasi ukuran partikel pasir dan kecepatan fluida. Didapatkan hasil berupa profil erosi dan laju erosi pada elbow pipa yang dibandingkan dengan hasil eksperimen. Hasil simulasi menunjukkan bahwa CFD mampu untuk memprediksi laju erosi secara baik untuk ukuran partikel 300 μm dengan error sebesar 14.75% dibandingkan ukuran partikel 150 μm yang memcapai error 271.5%. Terbentuk profil erosi berbentuk huruf 'V' pada elbow pipa vertikalhorizontal.
Environmental problems are still an important issue and cannot be resolved completely until now, even after the 1970s the United Nations established a world environmental day. Plastic waste is considered the most responsible for the problems of environmental damage today. Therefore, an innovation that comes from biodegradable material, with its biodegradable product is considered to be the answer to this environmental problem. This study examines how reporting on the environment is framed in online mass media, especially in relation to biodegradable material and biodegradable products. This is qualitative research, with the object of two Indonesian online news sites, namely www.detik.com and www.okezone.com. Data collection techniques used is document studies and data analysis techniques employed is Robert N. Entman's Framing analysis model which involves four elements, namely: define problems, diagnose causes, make moral judgment, and treatment recommendation. The findings of this study are that environmental issues have not dominated online media coverage, and the biodegradable issue has not been framed thoroughly by online media.
This research is aimed to get a better understanding on the effort of reducing the porosity level in aluminum alloys. The degassing process (2, 5 and 8 minutes) is done to reduce the hydrogen content in liquid aluminum and cooling rate modifications (13 °C / min, 20 °C / min and 26 °C / min) was performed to reduce the porosity by reducing the size of Dendrite Arm Spacing (DAS). The casting method used in this research is sand casting and raw materials were melted using an electric furnace at 720 °C. The microstructural images showed the DAS size are decreased by size from 137.3 μm to 87.58 μm obtained from cooling rates of 13 °C / min and 26 °C / min respectively. In the other hand, the level of porosity is also decreased from 3.58% at 2 min degassing and the cooling rate of 13 °C / min to 1.8% at 5 min degassing and 26 °C / min cooling rate. Furthermore, the tensile test results show that the value of tensile strength increases when the DAS size and porosity level are smaller. The highest ultimate tensile strength value is 105.9 and the lowest is 70,53 MPa.
F1Abstrak-Ditemukan kegagalan pada poros pompa multistage di Pabrik Gula Gending yang baru beroperasi beberapa bulan dari 4 tahun umur pakai yang direncanakan. Kegagalan pada poros tersebut adalah patah dan aus pada ulirnya. Menurut ASTM A291, material standar untuk poros tersebut adalah ASSAB 705. Namun pengujian komposisi dan kekerasan menunjukkan bahwa poros pompa yang patah tidak sesuai dengan standar ASSAB 705. Oleh karena itu dilakukan penelitian mengenai pengaruh variasi parameter perlakuan panas tempering terhadap baja ASSAB 705 untuk aplikasi poros pompa. Perlakuan yang diberikan adalah water quench hardening dengan temperatur 815 o C dan waktu tahan 30 menit. Kemudian dilakukan tempering dengan temperatur 300 o C, 350 o C dan 400 o C dimana variasi waktu tahan tiap temperatur tersebut adalah 60 menit dan 120 menit. Uji metalografi menunjukkan bahwa semakin tinggi temperatur dan waktu tahan, martensit tampak semakin sedikit akibat terdekomposisi menjadi struktur ferrit dan bainit. Uji XRD memberikan hasil yang sejalan dengan fenomena tersebut, yaitu berkurangnya struktur BCT (martensit) seiring bertambahnya struktur BCC (bainit dan ferrit) pada temperatur dan waktu tahan yang makin tinggi. Hal ini tentu berdampak pada kekerasan dan ketahanan ausnya. Spesimen dengan kekerasan dan ketahanan aus tertinggi adalah yang diberikan tempering dengan temperatur 300 o C dan waktu tahan 60 menit. Sedangkan yang memiliki kekerasan dan ketahanan aus paling rendah adalah yang diberikan tempering dengan temperatur 400 o C dan waktu tahan 120 menit.Kata Kunci-Poros pompa multistage, ASSAB 705, Perlakuan Panas, Kekerasan, Keausan.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.