A majority of well integrity problems originate from cracks of oil well cement. To address the crack issues, bespoke sodium silicate microcapsules were used in this study for introducing autonomous crack healing ability to oil well cement under high-temperature service conditions at 80 °C. Two types of sodium silicate microcapsule, which differed in their polyurea shell properties, were first evaluated on their suitability for use under the high temperature of 80 °C in the wellbore. Both types of microcapsules showed good thermal stability and survivability during mixing. The microcapsules with a more rigid shell were chosen over microcapsule with a more rubbery shell for further tests on the self-healing efficiency since the former had much less negative effect on the oil well cement strength. It was found that oil well cement itself showed very little healing capability when cured at 80 °C, but the addition of the microcapsules significantly promoted its self-healing performance. After healing for 7 days at 80 °C, the microcapsule-containing cement pastes achieved crack depth reduction up to ~58%, sorptivity coefficient reduction up to ~76%, and flexural strength regain up to ~27%. The microstructure analysis further confirmed the stability of microcapsules and their self-healing reactions upon cracking in the high temperature oil well cement system. These results provide a promising perspective for the development of self-healing microcapsule-based oil well cements.
Currently, the MgO expansion agent is widely used to reduce the cracking risk of concrete. The influence of MgO reactivity (50 s and 300 s) and dosage (0, 4 wt.% and 8 wt.%, by weight of binder) on the air void, pore structure, permeability and freezing–thawing (F–T) resistance of concrete were studied. The results indicate (1) the addition of 4–8 wt.% reactive MgO (with reactivity of 50 s and termed as M50 thereafter) and weak reactive MgO (with reactivity of 300 s and termed M300 thereafter) lowers the concrete’s compressive strength by 4.4–17.2%, 3.9–16.4% and 1.9–14.6% at 3, 28 and 180 days, respectively. The increase in MgO dosage and reactivity tends to further reduce the concrete strength at all hydration ages. (2) Permeability of the concrete is closely related to the pore structure. M50 can densify the pore structure and lower the fraction of large capillary pores at an early age, thus it is beneficial for the impermeability of concrete. In contrast, M300 can enhance the 180-day impermeability of concrete since it can densify the pore structure only at a late age. (3) The influence of MgO on F–T resistance is minor since MgO could not change the air void parameters. (5) MgO concretes exhibit obvious fractal characteristics. The fractal dimension of the pore surface (Ds) exhibits a close relationship with the permeability property of concrete. However, no correlation can be found between F–T resistance and Ds.
Magnesium ammonium phosphate cement (MAPC) prepared with ammonium dihydrogen phosphate (NH4H2PO4, ADP) and dead-burned Magnesium oxide (MgO) is a new type of rapid patch repair material for concrete structures. In order to reduce the material costs of MAPC mortar, manufactured limestone sands, being a more widely-available resource with lower cost, was investigated in this study as an alternative to quartz sands for the preparation of MAPC mortar. The limestone fines in manufactured sands were found to be the key factor that influences properties of MAPC mortar by causing bubbling and volume expansion before hardening. As a result, the mechanical strength of MAPC mortar decreased with the increasing content of limestone fines due to increased porosity. According to microstructure analysis, the mechanism of these negative effects can be inferred as the reaction between limestone fines and ADP with the gas generation of CO2 and NH3. This reaction mainly occurred during a short period before setting while most limestone fines remained unreactive in the hardened MAPC mortar. Based on the above detailed experimental findings on the effects of limestone fines in manufactured sand on the properties of MAPC mortar, this paper pointed out that effective defoaming methods for inhibiting bubbling was the key to the utilization of manufactured sands in preparation of high performance MAPC mortar.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.