Realization of advanced bio-interactive electronic devices requires mechanically compliant sensors with the ability to detect extremely large strain. Here, we design a new multifunctional carbon nanotube (CNT) based capacitive strain sensors which can detect strains up to 300% with excellent durability even after thousands of cycles. The CNT-based strain gauge devices exhibit deterministic and linear capacitive response throughout the whole strain range with a gauge factor very close to the predicted value (strictly 1), representing the highest sensitivity value. The strain tests reveal the presented strain gauge with excellent dynamic sensing ability without overshoot or relaxation, and ultrafast response at sub-second scale. Coupling these superior sensing capabilities to the high transparency, physical robustness and flexibility, we believe the designed stretchable multifunctional CNT-based strain gauge may have various potential applications in human friendly and wearable smart electronics, subsequently demonstrated by our prototypical data glove and respiration monitor.R ecent developments in flexible and stretchable electronics, either through structural consideration or by exploring novel materials 1,2 , have imparted otherwise rigid and brittle electronic devices mechanical compliance and bio-compatibility, paving the way for energy-efficient, lightweight, portable, wearable and even implantable electronics 3 . Examples include stretchable and large area display that can undergo complex deformations 4 , bio-inspired material and structural designs that enable bionic functions 5 , and printable sensory system capable of detecting planar strains, normal pressure, temperature, light, moisture and chemical/biological species 6 . Multifunctional sensors, in particular, with sensing abilities akin to or beyond those of human skin 6-12 , are essential for applications such as interactive electronics 13 , structural health monitoring 14 , smart clothing 15 , robotic systems with advanced sensing capabilities 16 , human motion detection 8 and so on. Among the various types of sensors, strain gauge is one of the most important smart sensors, which have been widely used in the measurements of strain, acceleration and tension, as well as structural health monitoring. Conventional strain gauges, made of metal foils, register resistance changes under tensile strains. Actually, mechanical compliance and large strain range (?5%), obviously not the case of metal foils, are required to meet the demands of wearable electronics 15 , human motion detection 8 and interactive robots 17 . Although mercury-in-rubber strain gauge has been used in the biological measurements for decades 18 , the maximum strain limit and toxicity of mercury still block their practically wide applications. In addition, the combination of conformability and optical transparency will facilitate intelligent electronics and self-powered robot where strain sensors are integrated with optoelectronic devices and direct observation through the devices is ne...

The well-defined silver (Ag) nanowires with five-twinned structure have been prepared by polyol reduction in the presence of poly(vinylpyrrolidone) (PVP K-30, 40 000). The obtained Ag nanowires are nearly monodispersed with an average diameter of 70 nm and length of 6 μm. It is confirmed from the results of thermogravimetric analysis (TGA), X-ray photoelectron spectroscopy (XPS), and Fourier transform Raman spectra (FT-Raman) that one monolayer of the PVP molecules might be absorbed on the surface of the Ag nanowires through Ag−O coordination. On the basis of the experimental analysis, the probable spatial conformation of the PVP molecules is supposed to be that the CH skeleton chain of the PVP is close to the surface of the Ag nanowires. The pyrrolidone ring might be tilted on the surface of the Ag nanowires through Ag:O coordination. These results may provide direct evidence for the role of the PVP molecules in the formation of the Ag nanowires.

We demonstrate a low-cost and effective method to fabricate hexagonally patterned, vertically aligned ZnO nanorod arrays. Selective wet-etching is used to develop the catalyzing gold particle hexagonal pattern with the aid of a polystyrene microsphere self-assembled monolayer. The gold particles have tunable sizes independent of the polystyrene microsphere's diameter and are inherently round in shape. Each ZnO rod is grown individually from a catalyzing site via catalyst-initiated epitaxy, and the original hexagonal periodicity is well-preserved. The rods have flat ends, and the diameters of the rods can be controlled well by the amount of source materials. This method provides a promising way to create ZnO one-dimensional nanostructures for applications as two-dimensional photonic crystal, sensor arrays, nanolaser arrays, and optoelectronic devices.