Microbial polyhydroxyalkanoates (PHAs) are promising biodegradable polymers that may alleviate some of the environmental burden of petroleum-derived polymers. The requirements for carbon substrates and energy for bioreactor operations are major factors contributing to the high production costs and environmental impact of PHAs. Improving the process productivity is an important aspect of cost reduction, which has been attempted using a variety of fed-batch, continuous, and semi-continuous bioreactor systems, with variable results. The purpose of this review is to summarize the bioreactor operations targeting high PHA productivity using pure cultures. The highest volumetric PHA productivity was reported more than 20 years ago for poly(3-hydroxybutryate) (PHB) production from sucrose (5.1 g L−1 h−1). In the time since, similar results have not been achieved on a scale of more than 100 L. More recently, a number fed-batch and semi-continuous (cyclic) bioreactor operation strategies have reported reasonably high productivities (1 g L−1 h−1 to 2 g L−1 h−1) under more realistic conditions for pilot or industrial-scale production, including the utilization of lower-cost waste carbon substrates and atmospheric air as the aeration medium, as well as cultivation under non-sterile conditions. Little development has occurred in the area of fully continuously fed bioreactor systems over the last eight years.

A recombinant of Pseudomonas putida LS461 (deletion of the phaC1phaZphaC2 genes) was constructed by introducing cosmid JC123 carrying a novel phaC1 16 gene from a metagenomic clone. The resulting strain, P. putida LS46123, was able to synthesize polyhydroxyalkanoate (PHA) polymers with novel monomer compositions when cultured on glucose or free fatty acids, and accumulated PHAs from 9.24% to 27.09% of cell dry weight. The PHAs synthesized by P. putida LS46123 contained up to 50 mol % short chain length subunits (3-hydroxybutyrate and 3-hydroxyvalerate), with the remaining monomers consisting of various medium chain length subunits. The PhaC1 16 protein expressed by P. putida LS46123 had an amino acid sequence similarity of 45% with the PhaC1 protein of the parent strain, P. putida LS46. Predicted 3D structures of the PhaC1 16 proteins from P. putida LS46123 and P. putida LS46 revealed several differences in the numbers and locations of protein secondary structures. The physical and thermal properties of the novel polymers synthesized by P. putida LS46123 cultured with glucose or free fatty acids differed significantly from those produced by P. putida LS46 grown on the same substrates. PHA polymers with different subunit compositions, and hence different physical and thermal properties, can be tailor-made using novel PHA synthase for specific applications.

Polyhydroxyalkanoates (PHAs) are a diverse class of bio-polymers synthesized by bacteria, usually during imbalanced growth conditions. Optimizing PHA productivity is highly dependent on the bioreactor oxygen transfer rate (OTR), which is an important consideration for process performance and economics, particularly with increasing scale. Relatively few in-depth studies are available regarding the effect of OTR and dissolved oxygen content (DOC) on PHA formation, synthesis rates, composition, and characteristics. This review examines past research studies on the effect of low DOC environments on production of short-chain length (scl-) PHAs, synthesized by both pure and mixed cultures, in order to identify opportunities and gaps concerning the effect of DOC on production of medium-chain length (mcl-) PHAs, an area that has not been studied in detail. The literature indicates that production of scl-PHA (a reductive process) acts as an electron sink allowing cells to maintain balanced redox state at low DOC. Conversely, production of mcl-PHA via fatty acid de novo synthesis (also a reductive process) does not occur to any significant extent in low DOC environments, while mcl-PHA synthesis from fatty acids (an oxidative process) can be promoted in low DOC environments. The monomer composition, molecular mass, as well as physical and thermal properties of the polymer can change in response to OTR, but further research in this area is required for both scl- and mcl-PHAs. Process design and management of bioreactor OTR in PHA production might therefore be directed by the final application of the polymer rather than cost considerations.

No abstract

Economical production of medium-chain length polyhydroxyalkanoates (mcl-PHA) is dependent on efficient cultivation processes. This work describes growth and mcl-PHA synthesis characteristics of Pseudomonas putida LS46 when grown on medium-chain length fatty acids (octanoic acid) and lower-cost long-chain fatty acids (LCFAs, derived from hydrolyzed canola oil) in microaerophilic environments. Growth on octanoic acid ceased when the oxygen uptake rate was limited by the oxygen transfer rate, and mcl-PHA accumulated to 61.9% of the cell dry mass. From LCFAs, production of non-PHA cell mass continued at a rate of 0.36 g L h under oxygen-limited conditions, while mcl-PHA accumulated simultaneously to 31% of the cell dry mass. The titer of non-PHA cell mass from LCFAs at 14 h post-inoculation was double that obtained from octanoic acid in bioreactors operated with identical feeding and aeration conditions. While the productivity for octanoic acid was higher by 14 h, prolonged cultivation on LCFAs achieved similar productivity but with twice the PHA titer. Simultaneous co-feeding of each substrate demonstrated the continued cell growth under microaerophilic conditions characteristic of LCFAs, and the resulting polymer was dominant in C8 monomers. Furthermore, co-feeding resulted in improved PHA titer and volumetric productivity compared to either substrate individually. These results suggest that LCFAs improve growth of P. putida in oxygen-limited environments and could reduce production costs since more non-PHA cell mass, the cellular factories required to produce mcl-PHA and the most oxygen-intensive cellular process, can be produced for a given oxygen transfer rate.