The changes of a sulphur content during refining in melting low-alloy and high-alloy steels (G17CrMoV5-10; GX12CrMoNiVNbN9-1) applied for large-dimension castings for the power engineering are presented in the hereby paper. The investigated steel was melted in the oxygen-recovery melting technology with an application of maximum 70% of the process scrap. In addition, after steel melting in the electric arc furnace (EAF), the secondary metallurgy was performed in the ladle furnace (LF). It was shown that the application of the secondary metallurgy by a synthetic slag in the ladle furnace and argon bubbling of a metal bath leads to obtaining in the final analysis: 0.0043-0.0046% of sulphur (a decrease of S content during refining in LF reached 40%). Current measurements of FeO in the slag and maintaining its content below 0.8%, support obtaining such low sulphur content in steel. So low level of the slag oxidizing is one of the necessary conditions for a deep desulphurisation of the metal bath. Without the secondary metallurgy the sulphur content in low-alloy cast steel was 0.007%, while 0.01% in high-alloy cast steel.Controlling of the gas (oxygen, nitrogen) content during steel melting and correcting the amount of additions (e.g. deoxidants), allowed to obtain the low oxygen content (below 45 ppm for two investigated steel grades) and nitrogen content (88 ppm for low-alloy steel and 330 ppm for high-alloy steel), which warrants a good combination of strength and plastic properties.Keywords: Cast steel for power industry, Melting technology, Electric arc furnace, Ladle furnace, Desulphurisation W pracy przedstawiono zmiany zawartości siarki podczas rafinacji w czasie wytapiania stali nisko-i wysokostopowej (G17CrMoV5-10; GX12CrMoNiVNbN9-1) stosowanej na wielkogabarytowe odlewy dla energetyki. Badaną stal wytopiono w technologii odzyskowo-tlenowej z zastosowaniem maksymalnie 70% złomu własnego. Dodatkowo, po wytopieniu stali w piecu łukowym (EAF) przeprowadzono obróbkę pozapiecową w pieco-kadzi (LF). Wykazano, że zastosowanie obróbki pozapiecowej żużlem syntetycznym w pieco-kadzi i argonowania kąpieli metalowej prowadzi do uzyskania w analizie końcowej 0,0043-0,0046%S (zmniejszenie zawartości S podczas rafinacji w LF sięgało 40%). Uzyskaniu tak niskiej zawartości siarki w stali sprzyja m.in. bieżący pomiar FeO w żużlu i utrzymanie jego zawartości poniżej 0,8%. Tak niski poziom stopnia utlenienia żużla jest jednym z warunków koniecznym do dobrego odsiarczenia kąpieli metalowej. Bez obróbki pozapiecowej zawartość siarki w staliwie niskostopowym wynosiła 0,007%, natomiast dla staliwa wysokostopowego 0,01%. Kontrola zawartości gazów (tlenu i azotu) w czasie wytapiania stali i dokonywana korekta ilości wprowadzanych dodatków (np. odtleniaczy) doprowadziła do uzyskania niskiej zawartości tlenu (poniżej 45 ppm dla dwóch badanych gatunków stali) i azotu (88 ppm dla stali niskostopowej, 330 ppm dla stali wysokostopowej) gwarantująca dobrą kombinację właściwości wytrzymałościowych i plastycznych odlewów.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.