A critical issue for fusion plasma research is the erosion of the first wall of the experimental device due to impulsive heating from repetitive edge magneto-hydrodynamic (MHD) instabilities known as "edge-localized modes" (ELMs). Here, we show that the addition of small resonant magnetic field perturbations completely eliminates ELMs while maintaining a steady-state highconfinement (H-mode) plasma. These perturbations induce a chaotic behaviour in the magnetic field lines, which reduces the edge pressure gradient below the ELM instability threshold. The pressure gradient reduction results from a reduction in particle content of the plasma, rather than an increase in the electron thermal transport. This is inconsistent with the predictions of stochastic electron heat transport theory. These results provide a first experimental test of stochastic transport theory in a highly rotating, hot, collisionless plasma and demonstrate a promising solution to the critical issue of controlling edge instabilities in fusion plasma devices. Nature Physics. 3Maximizing the fusion power production in toroidally symmetric magnetic confinement devices (tokamaks 1,2 ) requires high-confinement (H-mode) plasma conditions that have high edge plasma pressures. A ubiquitous feature of these high edge pressure, steady state, H-mode tokamak plasmas is repetitive instabilities known as "edge-localized modes" (ELMs) which release a significant fraction of the thermal energy of the plasma to the first wall of the device.These instabilities are a class of ideal magneto-hydrodynamic (MHD) modes produced in a high pressure gradient region at the plasma edge (called the "pedestal") where pressure gradient driven "ballooning" modes can couple to current density driven "peeling" modes 3 . While ELMs provide a natural transport process that controls the core plasma density and edge impurity ion penetration, they also represent a significant concern for burning plasma devices such as the ! n e ped ) to achieve significant fusion power gain factors, Q ≥ 10, they must operate below ! " e * = 0.1. In this case each ELM is expected to expel up to 20% of the pedestal energy over a time interval of a few hundred µs. If allowed to reach plasma-facing wall components, energy impulses of this magnitude will cause increased erosion of plasma facing components and significantly reduce their lifetime 5,6 . Thus, controlling ELMs by replacing the energy impulses with an equivalent but more continuous transport process is a high priority issue for tokamak fusion research.A particularly appealing ELM control approach in low the RMP field causes a larger change in the edge particle balance (i.e., changes in the balance between outward particle transport and edge particle sources and sinks) rather than in the thermal transport across the pedestal is both surprising and theoretically challenging.As in previous high is satisfied, these small ELMs disappear, leaving the plasma in a very quiet state (Fig. 3a), and the pedestal density ! n e ped begins to fall w...

Understanding the physics of the edge pedestal and edge localized modes (ELMs) is of great importance for ITER and the optimization of the tokamak concept. The peeling-ballooning model has quantitatively explained many observations, including ELM onset and pedestal constraints, in the standard H-mode regime. The ELITE code has been developed to efficiently evaluate peeling-ballooning stability for comparison to observation and predictions for future devices. We briefly present recent progress in the peelingballooning model, including studies of the apparent power dependence of the pedestal, and studies of the impact of sheared toroidal flow. Nonlinear 3D simulations of ELM dynamics using the BOUT code are also described, leading to an emerging understanding of the physics of the onset and dynamics of ELMs in the standard intermediate to high collisionality regime. Recently, highly promising low collisionality regimes without ELMs have been discovered, including the quiescent H-mode (QH) and resonant magnetic perturbation (RMP) regimes. We present recent observations of the density, shape and rotation dependence of QH discharges, and studies of the peeling-ballooning stability in this regime. We propose a model of the QH-mode in which the observed edge harmonic oscillation (EHO) is a saturated kink/peeling mode which is destabilized by current and rotation, and drives significant transport, allowing a near steady-state edge plasma. The model quantitatively predicts the observed density dependence, and qualitatively predicts observed mode structure, rotation dependence, and outer gap dependence. Low density RMP discharges are found to operate in a similar regime, but with the EHO replaced by an applied magnetic perturbation.

Cross-field fluctuation-driven transport is studied in edge and scrape-off layer (SOL) plasmas in the DIII-D tokamak using a fast reciprocating Langmuir probe array allowing local measurements of the fluctuation-driven particle and heat fluxes. Two different non-diffusive mechanisms that can contribute strongly to the cross-field transport in the SOL of high-density discharges are identified and compared. The first of these involves intermittent transport events that are observed at the plasma separatrix and in the SOL. Intermittence has qualitatively similar character in L-mode and ELM-free H-mode. Low-amplitude ELMs observed in high-density H-mode produce in the SOL periods with cross-field transport enhanced to L-mode levels and featuring intermittent events similar to those in L-mode. The intermittent transport events are compatible with the concept of plasma filaments propagating across the SOL due to E × B drifts. The intermittent character of the transport in the SOL is also in agreement with predictions of the non-linear numerical simulations performed with an imposed driving flux. Another type of non-diffusive transport is often seen in high-density H-modes with prolonged ELM-free periods, where the transport near the separatrix is dominated by quasi-coherent modes driving particle and/or heat fluxes exceeding L-mode levels. These modes may play an important role by providing particle and/or heat exhaust between ELMs.

Recent QH-mode research on DIII-D [J. L. Luxon et al., Plasma Physics and Controlled Nuclear Fusion Research 1996 (International Atomic Energy Agency, Vienna, 1987), Vol. I, p. 159] has used the peeling-ballooning modes model of edge magnetohydrodynamic stability as a working hypothesis to organize the data; several predictions of this theory are consistent with the experimental results. Current ramping results indicate that QH modes operate near the edge current limit set by peeling modes. This operating point explains why QH mode is easier to get at lower plasma currents. Power scans have shown a saturation of edge pressure with increasing power input. This allows QH-mode plasmas to remain stable to edge localized modes (ELMs) to the highest powers used in DIII-D. At present, the mechanism for this saturation is unknown; if the edge harmonic oscillation (EHO) is playing a role here, the physics is not a simple amplitude dependence. The increase in edge stability with plasma triangularity predicted by the peeling-ballooning theory is consistent with the substantial improvement in pedestal pressure achieved by changing the plasma shape from a single null divertor to a high triangularity double null. Detailed ELITE calculations for the high triangularity plasmas have demonstrated that the plasma operating point is marginally stable to peeling-ballooning modes. Comparison of ELMing, coinjected and quiescent, counterinjected discharges with the same shape, current, toroidal field, electron density, and electron temperature indicates that the edge radial electric field or the edge toroidal rotation are also playing a role in edge stability. The EHO produces electron, main ion, and impurity particle transport at the plasma edge which is more rapid than that produced by ELMs under similar conditions. The EHO also decreases the edge rotation while producing little change in the edge electron and ion temperatures. Other edge electromagnetic modes also produce particle transport; this includes the incoherent, broadband activity seen at high triangularity. Pedestal values of ν* and βT bracketing, those required for International Experimental Thermonuclear Reactor [Nucl. Fusion 39, 2137 (1999)] have been achieved in DIII-D, demonstrating the QH-mode edge densities are sufficient for future devices.

H-mode operation is the choice for next-step tokamak devices based either on conventional or advanced tokamak physics. This choice, however, comes at a significant cost for both the conventional and advanced tokamaks because of the effects of edge-localized modes (ELMs). ELMs can produce significant erosion in the divertor and can affect the β limit and reduced core transport regions needed for advanced tokamak operation. Recent experimental results from DIII-D have demonstrated a new operating regime, the quiescent H-mode regime, which solves these problems. We have achieved quiescent H-mode operation which is ELM-free and yet has good density control. In addition, we have demonstrated that an internal transport barrier can be produced and maintained inside the H-mode edge barrier for long periods of time (>3.5 s or >25 energy confinement times τ E ). By forming the core barrier and then stepping up the input power, we have achieved β N H 89 = 7 for up to 10 times the τ E of 160 ms. The β N H 89 values of 7 substantially exceed the value of 4 routinely achieved in standard ELMing H-mode. The key factors in creating the quiescent H-mode operation are neutral beam injection in the direction opposite to the plasma current (counter injection) plus cryopumping to reduce the density. Density control in the quiescent H-mode is possible because of the presence of an edge MHD oscillation, the edge harmonic oscillation, which enhances the edge particle transport while leaving the energy transport unaffected.