No abstract

A predictive model is proposed that quantitatively describes the synergistic behavior of the electrical conductivities of CNTs and graphene in CNT:graphene hybrids. The number of CNT-to-CNT, graphene-to-graphene, and graphene-to-CNT contacts is calculated assuming a random distribution of CNTs and graphene particles in the hybrids and using an orientation density function. Calculations reveal that the total number of contacts reaches a maximum at a specific composition and depends on the particle sizes of the graphene and CNTs. The hybrids, prepared using inkjet printing, are distinguished by higher electrical conductivities than that of 100% CNT or graphene at certain composition ratios. These experimental results provide strong evidence that this approach involving constituent element contacts is suitable for investigating the properties of particulate hybrid materials.

No abstract

Nanostructured flexible electrodes with biological compatibility and intimate electrochemical coupling provide attractive solutions for various emerging bioelectronics and biosensor applications. Here, we develop all-inkjet-printed flexible nanobio-devices with excellent electrochemical coupling by employing amphiphilic biomaterial, an M13 phage, numerical simulation of single-drop formulation, and rational formulations of nanobio-ink. Inkjet-printed nanonetwork-structured electrodes of single-walled carbon nanotubes and M13 phage show efficient electrochemical coupling and hydrostability. Additive printing of the nanobio-inks also allows for systematic control of the physical and chemical properties of patterned electrodes and devices. All-inkjet-printed electrochemical field-effect transistors successfully exhibit pH-sensitive electrical current modulation. Moreover, all-inkjet-printed electrochemical biosensors fabricated via sequential inkjet-printing of the nanobio-ink, electrolytes, and enzyme solutions enable direct electrical coupling within the printed electrodes and detect glucose concentrations at as low as 20 μM. Glucose levels in sweat are successfully measured, and the change in sweat glucose levels is shown to be highly correlated with blood glucose levels. Synergistic combination of additive fabrication by inkjet-printing with directed assembly of nanostructured electrodes by functional biomaterials could provide an efficient means of developing bioelectronic devices for personalized medicine, digital healthcare, and emerging biomimetic devices.

This paper presents the experimental results of an evaluation of the recovery behavior of Fe-based shape memory alloys (Fe-SMAs) under different restraints. For the study, three types of Fe-SMA (FSMA-A, FSMA-B, FSMA-C) were produced. As a result of the direct tensile test, the yield strength of the FSMA-A specimen was nearly 34% higher than the strength of FSMA-B and FSMA-C. Under free restraint, the recovery strains are 0.00956, 0.01445, and 0.01977 for FSMA-A, FSMA-B and FSMA-C specimens, respectively, after activation when the pre-strain is 0.04, and the heating temperature 200 °C. Under rigid restraint, the final recovery stresses are 518, 391 and 401 MPa for FSMA-A, FSMA-B, FSMA-C specimens after activation when a pre-strain of 0.04 and heating temperature 200 °C. Additionally, under the rigid restraint, the effect of pre-strain on the final recovery stress was insignificant, whereas the final recovery stress increased as the heating temperature increased. When Fe-SMA was constrained during cooling, the recovery stress is 50% lower than under rigid restraint. Hence, in order to develop a large recovery stress, Fe-SMA must be constrained during heating. In addition, a method for calculating the effective confining stress of the Fe-SMA coupler for pipe joining was proposed based on the experimental results.

The resistance change of carbon nanotube (CNT)/polymer composites during stress relaxation depended strongly on the CNT concentration and aspect ratio.At low concentration, the resistance of the composites increased regardless of aspect ratio of CNTs as relaxation progressed, while the relaxation modulus accordingly decreased. This trend changed with CNT concentration. To inves-

No abstract

Recently, a new type of LNG tank named "KC-1 membrane LNG tank" has been developed by Korean Gas Corporation (KOGAS), and Samsung Heavy Industries (SHI) is currently building KC-1 membrane type LNG carriers. Unlike other LNG tanks, the KC-1 membrane LNG tank has a single-insulation structure rather than a double-insulation structure. For a given tank's boundary condition, heat transfer analysis is performed from the external to the internal environment of the LNG tank by numerical simulation for three tanks. In each tank, the main thermally resistant layer of insulation is assembled with a High density rigid Polyurethane Foam (H-PUF), which is blown with one of three different types of hydrofluorocarbons-namely-HFC-365mfc, 245fa, and 245fa-e (enhanced). Advantage of such blowing agents is that it has a lower Ozone Depletion Potential (ODP) than HCFC-141b or carbon dioxide ( ) that has been used in the past as well as having low thermal conductivity. A Reduced Order Model is utilized to a 3-dimensional section of the insulation to calculate equivalent thermal conductivity. The equivalent thermal conductivity of the insulation is then applied to the rest of LNG tank, reducing the size of tank simulation domain as well as computation time. Tank's two external and internal boundary conditions used are those defined by the International Code for the Construction and Equipment of Ships Carrying Liquefied Gases in Bulk (IGC) and the United States Coast Guard (USCG) conditions. Boil-off Rate (BOR) of the tank that has the insulation with H-PUF blown with respectively..