Calcific aortic valvular disease (CAVD) is the most prevalent valvular pathology in the United States. Development of a pharmacologic agent to slow, halt, or reverse calcification has proven to be unsuccessful as still much remains unknown about the mechanisms of disease initiation. Although in vitro models of some features of CAVD exist, their utility is limited by the inconsistency of the size and time course of the calcified cell aggregates. In this study, we introduce and verify a highly reproducible in vitro method for studying dystrophic calcification of cardiac valvular interstitial cells, considered to be a key mechanism of clinical CAVD. By utilizing micro-contact printing, we were able to consistently reproduce cell aggregation, myofibroblastic markers, programmed cell death, and calcium accumulation within aggregates of 50-400 μm in diameter on substrates with moduli from 9.6 to 76.8 kPa. This method is highly repeatable, with 70% of aggregates staining positive for Alizarin Red S after one week in culture. Dense mineralized calcium-positive nanoparticles were found within the valvular interstitial cell aggregates as shown by scanning electron microscopy (SEM) and energy dispersive spectrometry (EDS). The area of micro-contact printed aggregates staining positive for caspase 3/7 activity increased from 5.9 ± 0.9% to 12.6 ± 4.5% over one week in culture. Z-VAD-FMK reduced aggregates staining positive for Alizarin Red S by 60%. The state of cell stress is hypothesized to play a role in the disease progression; traction force microscopy indicates high substrate stresses along the aggregate periphery which can be modulated by altering the size of the aggregates and the modulus of the substrate. Micro-contact printing is advantageous over the currently used in vitro model as it allows the independent study of how cytokines, substrate modulus, and pharmacologic agents affect calcification. This controlled method for aggregate creation has the potential to be used as an in vitro assay for the screening of promising therapeutics to mitigate CAVD.
Stress fields emerging from the transfer of forces between cells within multicellular systems are increasingly being recognized as major determinants of cell fate. Current analytical and numerical models used for the calculation of stresses within cell monolayers assume homogeneous contractile and mechanical cellular properties; however, cell behavior varies by region within constrained tissues. Here, we show the impact of heterogeneous cell properties on resulting stress fields that guide cell phenotype and apoptosis. Using circular micropatterns, we measured biophysical metrics associated with cell mechanical stresses. We then computed cell-layer stress distributions using finite element contraction models and monolayer stress microscopy. In agreement with previous studies, cell spread area, alignment, and traction forces increase, whereas apoptotic activity decreases, from the center of cell layers to the edge. The distribution of these metrics clearly indicates low cell stress in central regions and high cell stress at the periphery of the patterns. However, the opposite trend is predicted by computational models when homogeneous contractile and mechanical properties are assumed. In our model, utilizing heterogeneous cell-layer contractility and elastic moduli values based on experimentally measured biophysical parameters, we calculate low cell stress in central areas and high anisotropic stresses in peripheral regions, consistent with the biometrics. These results clearly demonstrate that common assumptions of uniformity in cell contractility and stiffness break down in postconfluence confined multicellular systems. This work highlights the importance of incorporating regional variations in cell mechanical properties when estimating emergent stress fields from collective cell behavior.
This paper investigates the galling behaviour of a range of hard coatings applied to tooling surfaces during the sheet forming of an aluminium alloy workpiece. A total of three types of tooling materials were investigated, two of which were subject to PVD deposited coatings of AlCrN, CrN and DLC applied to the working surface. The third tooling material had undergone induction heating, plasma-nitriding and polishing. To evaluate the galling behaviour of the applied coatings, a tribological evaluation was conducted using a pin-on-disc test set-up at a constant load and varying temperature. The coated discs, replicating the tooling material, were tested against aluminium alloy pins AA6082 and AA7075 representing the workpiece material. This investigation indicated that the friction and galling behaviour of aluminium is highly dependent on temperature, and the use of two different aluminium pins had no significant effect. At room temperature, it was found that carbon-based coatings provide the lowest friction and the best protection against galling, whilst nitride-based treatments exhibit better performance at high temperature. Moreover, at elevated temperatures, coated tools exhibit superior anti-galling properties compared to uncoated tools.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.