No abstract

No abstract

No abstract

A 13.56 MHz plasma jet discharge, called a plasma pencil, was investigated. Rotational and excitation temperatures, and electron number densities for the pencil under and without sample load were calculated using OH band spectra, Ar lines and Hb line, respectively. The rotational temperatures were found to be relatively low at about 800 K, however, excitation temperatures exceeded 4000 K. The plasma was found to be strongly non-isothermal. Some atomic lines of elements were easily observed. Aqueous solution-based aerosols were incorporated into the plasma without desolvation. Standard water solutions of the elements were nebulized into the plasma. The Ar carrier gas and Ar plasma gas flow rates were 0.3 and 4.0 l min À1 , respectively. The forwarded power was 140 W. Intensities of the atomic lines, temperatures and electron number densities along the discharge tube were acquired in different positions from the aerosol entrance and an optimal position providing the best signal-to-noise ratio for each line intensity was established. Calibration dependencies for Ca, Cu, Mg, Zn, Li, Na were measured in the rage of 1-100 mg l À1 . 3-sigma detection limits in the best observation axial position were (mg l À1 ): 27 (Ca), 49 (Cu), 58 (Mg), 40 (Li), 13 (Na) and 180 (Zn).

A pulsed, frequency-quadrupled Nd:YAG laser (266 nm, 10 Hz) coupled to an inductively coupled plasma atomic emission spectrometer (ICP-AES) was employed for depth profiling by ablation of a pyrolytically deposited Sn layer (300 nm) on float glass. The procedure consisted of performing individual ablation cycles (layer-by-layer). A raster with stroke distance of either 50 microm or 200 microm (the raster density) was used as an ablation pattern. The ablation was stopped after each cycle and the peak area of the resulting transient optical signal of the ICP discharge was plotted against the cycle number. The ablation rate of 90 to 20 nm per cycle at a low-energy pulse (6 mJ to 1 mJ) was determined by profilometry. A beam masking was employed to attenuate the laser shot energy and to eliminate the peripheral irregularity of the beam profile. Almost uniform removal of the square area (1 mm x 1 mm) of the coating by ablation was achieved by combining the fitted raster density, beam masking, focusing and beam energy. Different ablation processes were distinguished in cases of the tin coating and the uncoated glass surface. While the coating was mainly evaporated, the uncoated glass surface exhibited a crumbling associated with production of glass powder. This was confirmed by electron microscopy observations. The measured acoustic signal followed the behavior of the emission intensity of the Sn line and was supposed to be proportional to the amount of Sn vapors. The emission intensity depth profile of the Sn coating with graded structure was obtained, which qualitatively corresponded with the depth profile measured by secondary ion mass spectrometry.

No abstract

Potential of infrared laser ablation (LA) coupled with ICP-AES as a technique suitable for the determination of trace elements (Zn, Cu, Ni, Cr, and V) in agricultural soils was studied. Operating parameters such as laser beam energy, laser beam focusing with respect to the sample surface, and velocity of the sample translation in the plane perpendicular to the laser beam were optimized. Soil samples were mixed with powdered Ag as a binder, and an internal standard (GeO(2)), and pressed into pellets. Calibration samples were prepared by adding known amounts of oxides of elements of interest into soils of known elemental composition and then processed in the same way as the analyzed samples. Calibration curves were found to be linear at least up to several hundreds of mg kg(-1) for the elements of interest. The elemental contents obtained by using LA-ICP-AES were compared with those obtained by analysis using wet chemistry followed by ICP-AES with pneumatic nebulization (PN). The results were in good agreement. Accuracy was also tested using certified reference soils with a bias not exceeding 10% relative.

The possibility of determining selenium in blood serum using inductively coupled plasma emission spectrometry with conventional pneumatic nebulization was studied. A high-resolution spectrometer (SBW=6 pm) with laterally viewed ICP was employed. Analysis with conventional pneumatic nebulization could overcome laborious and demanding digestion, which is necessary for hydride generation. A pressure digestion with nitric acid at 160 degrees C was sufficient to decrease the carbon content in the serum sample to 5%-10% of its original value. Spectral interference of the CN band was observed and mathematically corrected. It was found that the carbon-induced selenium line emission enhancement occurred even under ICP optimized conditions. A method of determination was developed and applied to the analysis of blood serum. True limit of detection in real samples is 0.01-0.02 mg/L and the limit of quantification (RSD 10%) is 0.03-0.07 mg/L using Se I 196.090 nm line at an integration time of 10-2 s. The method was tested by analysis of porcine blood serum and the serum reference material Seronorm MI 0181.