No abstract

Synthetic biopolymers are effective cues to replace damaged tissue in the tissue engineering (TE) field, both for in vitro and in vivo application. Among them, poly-l-lactic acid (PLLA) has been highlighted as a biomaterial with tunable mechanical properties and biodegradability that allows for the fabrication of porous scaffolds with different micro/nanostructures via various approaches. In this review, we discuss the structure of PLLA, its main properties, and the most recent advances in overcoming its hydrophobic, synthetic nature, which limits biological signaling and protein absorption. With this aim, PLLA-based scaffolds can be exposed to surface modification or combined with other biomaterials, such as natural or synthetic polymers and bioceramics. Further, various fabrication technologies, such as phase separation, electrospinning, and 3D printing, of PLLA-based scaffolds are scrutinized along with the in vitro and in vivo applications employed in various tissue repair strategies. Overall, this review focuses on the properties and applications of PLLA in the TE field, finally affording an insight into future directions and challenges to address an effective improvement of scaffold properties.

Scaffolds suitable for tissue engineering applications like dermal reconstruction were prepared by Thermally Induced Phase Separation (TIPS) starting from a ternary solution PLLA/dioxane/water. The experimental protocol consisted of three consecutive steps, a first quench from the homogeneous solution to an appropriate demixing temperature (within the metastable region), a holding stage for a given residence time, and a final quench from the demixing temperature to a low temperature (within the unstable region). A large variety of morphologies, in terms of average pore size and interconnection, were obtained upon modifying the demixing time and temperature, owing to the interplay of nucleation and growth processes during the residence in the metastable state. An interesting combination of micro and macroporosity was observed for long residence times in the metastable state (above 30 min at 35 degrees C). Preliminary degradation tests in a biological mimicking fluid (D-MEM with bovine serum) showed a significant weight loss during the initial stages (ca. 30% in 30 days) related to the degradation of the amorphous part, followed by a negligible weight loss in the next days (few percent from 30 to 60 days).

In this paper, an extended version of the continuous class-mode power amplifier (PA) design approach is presented. A new formulation describing the current waveform in terms of just two additional parameters, while maintaining a constant half-wave rectified sinusoidal voltage waveform, allows multiple solutions of fundamental and second-harmonic impedances that provide optimum performance to be computed. By varying only the imaginary parts of fundamental and second-harmonic impedances, it is shown that output performance in terms of power and efficiency is maintained constant and equal to that achievable from the standard class-. Indeed, when presenting resistive second-harmonic impedances, it will be demonstrated that the fundamental load can be adjusted to maintain satisfactory output performances greater than a certain predetermined target value. The measurements, conducted on a GaAs pHEMT device at 1 GHz, show a good agreement with the theoretical analysis, revealing drain efficiencies greater than 70% for a very large range of load solutions, which can translate to an ability to accommodate reactive impedance variations with frequency when designing broadband PAs.Index Terms-Broadband amplifiers, microwave devices, microwave measurements, power amplifiers (PAs), radio frequency (RF).

No abstract

Solidification in industrial processes very often involves flow fields, high thermal gradients and high pressures: the development of a model able to describe the polymer behavior becomes complex. Recently a new equipment has been developed and improved to study the crystallization of polymers when quenched under pressure. An experimental apparatus based on a modified, special injection moulding machine has been employed. Polymer samples can be cooled at a known cooling rate up to 100°C/s and under a constant pressure up to 40 MPa. Density, Micro Hardness (MH), Wide angle X‐ray diffraction (WAXD), and annealing measurements were then used to characterize the obtained sample morphology. Results on one iPP sample display a lower density and a lower density dependence on cooling rate for increasing pressure. Micro hardness confirms the same trend. A deconvolution technique of WAXD patterns is used to evaluate the final phase content of samples and to assess a crystallization kinetics behavior. A master curve approach to explain iPP behavior under pressure and high cooling rates was successfully applied on density results. On the basis of this simple model it is possible to predict the final polymer density by superposition of the effect of cooling rate and the effect of pressure in a wide range of experimental conditions.

No abstract

Organ-on-chips are miniaturised devices aiming at replacing animal models for drug discovery, toxicology and studies of complex biological phenomena. The field of Organ-On-Chip has grown exponentially, and has led to the formation of companies providing commercial Organ-On-Chip devices. Yet, it may be surprising to learn that the majority of these commercial devices are made from Polydimethylsiloxane (PDMS), a silicone elastomer that is widely used in microfluidic prototyping, but which has been proven difficult to use in industrial settings and poses a number of challenges to experimentalists, including leaching of uncured oligomers and uncontrolled adsorption of small compounds. To alleviate these problems, we propose a new substrate for organ-on-chip devices: Polylactic Acid (PLA). PLA is a material derived from renewable resources, and compatible with high volume production technologies, such as microinjection moulding. PLA can be formed into sheets and prototyped into desired devices in the research lab. In this article we uncover the suitability of Polylactic acid as a substrate material for Microfluidic cell culture and Organ-on-a-chip applications. Surface properties, biocompatibility, small molecule adsorption and optical properties of PLA are investigated and compared with PDMS and other reference polymers.