Background and Objectives Suboptimal management of postcraniotomy pain causes sympathetic and hemodynamic perturbations, leading to deleterious effects on the neurological system and overall patient outcome. Opioids are the mainstay of postoperative pain management but have various problems when given in high doses, or for prolonged durations in neurosurgical patients. The ideal method of pain control following craniotomy generally relies on a combination of various drugs. Oral pregabalin may be an attractive alternative in these patients. Materials and Methods Sixty, American Society of Anesthesiologists class I and II patients posted for elective supratentorial craniotomy, aged 18 and 60 years, were randomly assigned into three groups of 20 each to receive oral placebo (Group A), pregabalin 75 mg (Group B), or pregabalin 150 mg (Group C) before the induction of anesthesia. At the end of the surgery, patient-controlled analgesia was started with intravenous fentanyl. Visual analog scale (VAS) score was recorded every 2 hours for 24 hours, along with total postoperative fentanyl requirement. Results There were no differences in sex, duration of surgery or anesthesia and total intraoperative fentanyl administered among the three groups. The median postoperative VAS score (Group A—18.0, Group B—20, and Group C—22.0; p = 0.63) was similar in all the groups. However, postoperative fentanyl requirement over 24 hours was least in the group that received 150 mg pregabalin (Group A—190 μg, Group B—240 μg, and Group C—100 μg; p = 0.03). Conclusions Even though pain scores were not significantly different, patients receiving 150 mg oral pregabalin required the least amount of postoperative opioids.

No abstract

OBJECTIVE:To investigate the effect of different intracoronal bleaching methods on the shear bond strength and site of failure of ceramic brackets.MATERIALS AND METHODS:Sixty freshly extracted human maxillary incisors were randomly divided into four groups (n = 15). Endodontic access cavity was prepared and root canals were filled, root fillings were removed 2mm apical to the cementoenamel junction, and a 2-mmthick layer of glass ionomer cement base was applied. Group 1 served as the control. Intracoronal bleaching was performed with 35% carbamide peroxide in group 2, sodium perborate in group 3, and 37.5% hydrogen peroxide in group 4. The teeth were immersed in artificial saliva for 4 weeks before bracket bonding. Ceramic brackets were bonded with composite resin and cured with LED light. After bonding, the shear bond strength of the brackets was tested with a universal testing machine. The site of bond failure was determined by modified ARI (Adhesive Remnant Index).RESULTS:The highest value of shear bond strength was measured in control group (18.67 ± 1.59 MPa), which was statistically significant from groups 2,3, and 4. There was no significant difference between groups 2 and 4. The lowest shear bond strength was measured in group 3. ARI scores were not significant from each other.CONCLUSIONS:Intracoronal bleaching significantly affected the shear bond strength of ceramic brackets even after 4 weeks of bleaching. Bleaching with sodium perborate affects shear bond strength more adversely than does bleaching with other agents like hydrogen peroxide and carbamide peroxide.

Introduction: Proximal stripping of enamel is a routine clinical procedure employed in orthodontics to create space or for balancing tooth size discrepancies. This procedure may result in heat transfer to the pulp, predisposing it to histopathological changes and necrosis of the pulp tissue. Objective: To measure the temperature changes in the pulp chamber during different stripping procedures. Methods: 80 proximal surfaces of 40 extracted human premolar teeth were stripped using four techniques: diamond burs in air-rotor handpiece with air-water spray; diamond burs in micromotor handpiece, with and without a coolant spray; and hand-held diamond strips. A J-type thermocouple connected to a digital thermometer was inserted into the pulp chamber for evaluation of temperature during the stripping procedure. Results: An increase in the pulpal temperature was observed for all stripping method. Diamond burs in micromotor handpiece without coolant resulted in the higher increase in temperature (3.5oC), followed by hand-held diamond strips (2.8oC), diamond burs in air-rotor with air-water spray (1.9oC); and the smallest increase was seen with diamond burs in micromotor handpiece with coolant (1.65oC). None of the techniques resulted in temperature increase above the critical level of 5.5oC. Conclusion: Frictional heat produced with different stripping techniques results in increase in the pulpal temperature, therefore, caution is advised during this procedure. A coolant spray can limit the increase in temperature of the pulp.

No abstract