Aims. Future astrophysics and cosmic microwave background space missions operating in the far-infrared to millimetre part of the spectrum will require very large arrays of ultra-sensitive detectors in combination with high multiplexing factors and efficient lownoise and low-power readout systems. We have developed a demonstrator system suitable for such applications. Methods. The system combines a 961 pixel imaging array based upon Microwave Kinetic Inductance Detectors (MKIDs) with a readout system capable of reading out all pixels simultaneously with only one readout cable pair and a single cryogenic amplifier. We evaluate, in a representative environment, the system performance in terms of sensitivity, dynamic range, optical efficiency, cosmic ray rejection, pixel-pixel crosstalk and overall yield at an observation centre frequency of 850 GHz and 20% fractional bandwidth. Results. The overall system has an excellent sensitivity, with an average detector sensitivity NEP det = 3 × 10 −19 W/ √ Hz measured using a thermal calibration source. At a loading power per pixel of 50 fW we demonstrate white, photon noise limited detector noise down to 300 mHz. The dynamic range would allow the detection of ∼1 Jy bright sources within the field of view without tuning the readout of the detectors. The expected dead time due to cosmic ray interactions, when operated in an L2 or a similar far-Earth orbit, is found to be <4%. Additionally, the achieved pixel yield is 83% and the crosstalk between the pixels is <−30 dB. Conclusions. This demonstrates that MKID technology can provide multiplexing ratios on the order of a 1000 with state-of-the-art single pixel performance, and that the technology is now mature enough to be considered for future space based observatories and experiments.

Terahertz spectrometers with a wide instantaneous frequency coverage for passive remote sensing are enormously attractive for many terahertz applications, such as astronomy, atmospheric science and security. Here we demonstrate a wide-band terahertz spectrometer based on a single superconducting chip. The chip consists of an antenna coupled to a transmission line filterbank, with a microwave kinetic inductance detector behind each filter. Using frequency division multiplexing, all detectors are read-out simultaneously creating a wide-band spectrometer with an instantaneous bandwidth of 45 GHz centered around 350 GHz. The spectrometer has a spectral resolution of F/∆F = 380 and reaches photon-noise limited sensitivity. We discuss the chip design and fabrication, as well as the system integration and testing. We confirm full system operation by the detection of an emission line spectrum of methanol gas. The proposed concept allows for spectroscopic radiation detection over large bandwidths and resolutions up to F/∆F ∼ 1000, all using a chip area of a few cm 2 . This will allow the construction of medium resolution imaging spectrometers with unprecedented speed and sensitivity.

No abstract

For space observatories, the glitches caused by high energy phonons created by the interaction of cosmic ray particles with the detector substrate lead to dead time during observation. Mitigating the impact of cosmic rays is therefore an important requirement for detectors to be used in future space missions. In order to investigate possible solutions, we carry out a systematic study by testing four large arrays of Microwave Kinetic Inductance Detectors (MKIDs), each consisting of ∼ 960 pixels and fabricated on monolithic 55 mm × 55 mm × 0.35 mm Si substrates. We compare the response to cosmic ray interactions in our laboratory for different detector arrays: A standard array with only the MKID array as reference; an array with a low T c superconducting film as phonon absorber on the opposite side of the substrate; and arrays with MKIDs on membranes. The idea is that the low T c layer down-converts the phonon energy to values below the pair breaking threshold of the MKIDs, and the membranes isolate the sensitive part of the MKIDs from phonons created in the substrate. We find that the dead time can be reduced up to a factor of 40 when compared to the reference array. Simulations show that the dead time can be reduced to below 1 % for the tested detector arrays when operated in a spacecraft in an L2 or a similar far-Earth orbit. The technique described here is also applicable and important for large superconducting qubit arrays for future quantum computers. PACS numbers: Valid PACS appear hereData loss caused by cosmic ray hits on the instruments' detectors is one of the main concerns for space observatories. Cosmic rays are so energetic that they penetrate the satellite structure, reach the detectors, and deposit a fraction of their energy through ionization and atomic excitation. The deposited energy causes a cascade of high-energy phonons (ballistic phonons) that spread inside the detectors, trigger the detectors' response, and create glitches in the data stream. These glitches lead to significant dead time of the detectors and loss of integration efficiency 1 . Although cosmic ray interactions are strongest in space, even on earth the interaction rate is about a few events/min/cm 2 , posing possible issues especially for cryogenic superconducting circuits with large areas, such as quantum computing chips.Microwave Kinetic Inductance Detectors (MKIDs) 2,3 are pair breaking detectors that sense a change in Cooper pair density due to radiation absorption, in contrast to bolometric detectors, such as Transition Edge Sensors 4 , which measure temperature. Hence, MKIDs only sense energies larger than the gap energy of a superconductor film (2∆). In the Planck satellite, in which bolometers a) Electronic mail: K.Karatsu@sron.nl are used, short and long glitches are observed due to cosmic rays 5 . Short glitches, with a decay of 4-10 ms, are determined to be direct hits in the bolometer. Long glitches, with a time scale exceeding 10 ms, are interpreted as cosmic ray hits in the Si wafer. The measurements of cosmic ray ...

We present the design, fabrication, and full characterisation (sensitivity, beam pattern, and frequency response) of a background limited broadband antenna coupled kinetic inductance detector covering the frequency range from 1.4 to 2.8 THz. This device shows photon noise limited performance with a noise equivalent power of 2.5 × 10−19 W/Hz1∕2 at 1.55 THz and can be easily scaled to a kilo-pixel array. The measured optical efficiency, beam pattern, and antenna frequency response match very well the simulations.