As an effort to compare the influence of several types of functionalized carbon nanotubes (CNTs) upon the mechanical and thermal properties of nanocomposites prepared with a poly(e-caprolactone) (PCL) as matrix and functionalized CNTs as fillers; nanocomposites of PCL-CNTs were studied in this study. CNTs were synthesized by chemical vapor deposition using dry ethanol as the carbon source. High resolution scanning electron microscopy, high resolution transmission electron microscopy, and Raman and infrared spectroscopies were used to characterize the CNTs obtained. Four chemical synthesis routes were exploited to add different types of chemical groups onto the surface of purified CNTs. Specifically, the authors inserted: (i) N-methylpyrrolidine, (ii) carboxyl and hydroxyl, (iii) urethane, and (iv) phenylmethanol groups onto CNTs surface. Nanocomposites were synthesized by in situ polymerization of e-caprolactone (e-CL) in presence of 1 wt% of each type of functionalized CNTs. Young's moduli of the nanocomposites prepared with N-methylpyrrolidine or carboxyl and hydroxyl functionalized CNTs are higher than the one of pure PCL, whereas all the mechanical properties of the nanocomposites containing urethane or phenylmethanol groups evaluated at the break point were higher than those of pure PCL.
Four binary polymer blends containing poly [ethylene-co-(acrylic acid)] (PEAA) as one component, and poly(4-vinyl phenol-co-2-hydroxy ethyl methacrylate) (P4VPh-co-2HEMA) or poly(2-ethyl-2-oxazoline) (PEOx) or poly(vinyl acetate-co-vinyl alcohol) (PVAc-co-VA) or poly (vinylpyrrolidone-co-vinyl acetate) (PVP-co-VAc) as the other component were prepared and used as a matrix of a series of composite materials. These binary mixtures were either partially or completely miscible within the composition range studied and were characterized by differential scanning calorimetry (DSC) and Fourier transformed infrared spectroscopy (FTIR). Carbon nanotubes (CNTs) were prepared by a thermal treatment of polyester synthesized through the chemical reaction between ethylene glycol and citric acid over an alumina boat. High resolution transmission electron microscopy (HRTEM) was used to characterize the synthesized CNTs. Films of composite materials containing CNTs were obtained after evaporation of the solvent used to prepare solutions of the four types of binary polymer blends. Young's moduli of the composites were obtained by thermomechanical analysis at room temperature. Only one glass transition temperature was detected for several compositions on both binary blends and the composite material matrices. Evidence of hydrogen bond formation was recorded for both miscible blends and composite materials. The degree of crystallinity and Young's moduli of the CNT-polymer composites increased compared to the single polymer blends.
With the aim of exploring new materials and properties, we report the synthesis of a thermoplastic chain extended polyurethane membrane, with superior strength and toughness, obtained by incorporating two different concentrations of reactive cellulose nanocrystals (CNC) for potential use in kidney dialysis. Membrane nanocomposites were prepared by the phase inversion method and their structure and properties were determined. These materials were prepared from a polyurethane (PU) yielded from poly(1,4 butylene adipate) as a soft segment diol, isophorone diisocyanate (IPDI) and hexamethylenediamine (HMDA) as isocyanate and chain extender, respectively (hard segment), filled with 1 or 2% w/w CNC. Membrane preparation was made by the phase inversion method using N,N-dimethylformamide as solvent and water as nonsolvent, and subjected to dead-end microfiltration. Membranes were evaluated by their pure water flux, water content, hydraulic resistance and protein rejection. Polymers and nanocomposites were characterized by scanning electronic and optical microscopy, differential scanning calorimetry, infrared spectroscopy, strain stress testing and 13C solid state nuclear magnetic resonance. The most remarkable effects observed by the addition of CNCs are (i) a substantial increment in Young’s modulus to twenty-two times compared with the neat PU and (ii) a marked increase in pure water flux up to sixty times, for sample containing 1% (w/w) of CNC. We found that nanofiller has a strong affinity to soft segment diol, which crystallizes in the presence of CNCs, developing both superior mechanical and pure water flow properties, compared to neat PU. The presence of nanofiller also modifies PU intermolecular interactions and consequently the nature of membrane pores.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.