Biodegradable polymer composites from renewable resources are the next-generation of wood-like materials and are crucial for the development of various industries to meet sustainability goals. Functional applications like packaging, medicine, automotive, construction and sustainable housing are just some that would greatly benefit. Some of the existing industries, like wood plastic composites, already encompass given examples but are dominated by fossil-based polymers that are unsustainable. Thus, there is a background to bring a new perspective approach for the combination of microcrystalline cellulose (MCC) and nanofibrillated cellulose (NFC) fillers in bio-based poly (butylene succinate) matrix (PBS). MCC, NFC and MCC/NFC filler total loading at 40 wt % was used to obtain more insights for wood-like composite applications. The ability to tailor the biodegradable characteristics and the mechanical properties of PBS composites is indispensable for extended applications. Five compositions have been prepared with MCC and NFC fillers using melt blending approach. Young’s modulus in tensile test mode and storage modulus at 20 °C in thermo-mechanical analysis have increased about two-fold. Thermal degradation temperature was increased by approximately 60 °C compared to MCC and NFC. Additionally, to estimate the compatibility of the components and morphology of the composite’s SEM analysis was performed for fractured surfaces. The contact angle measurements testified the developed matrix interphase. Differential scanning calorimetry evidenced the trans-crystallization of the polymer after filler incorporation; the crystallization temperature shifted to the higher temperature region. The MCC has a stronger effect on the crystallinity degree than NFC filler. PBS disintegrated under composting conditions in a period of 75 days. The NFC/MCC addition facilitated the specimens’ decomposition rate up to 60 days
Ammonium persulfate has been known as an agent for obtaining nanocellulose in recent years, however most research has focused on producing cellulose nanocrystals. A lack of research about combined ammonium persulfate oxidation and common mechanical treatment in order to obtain cellulose nanofibrils has been identified. The objective of this research was to obtain and investigate carboxylated cellulose nanofibrils produced by ammonium persulfate oxidation combined with ultrasonic and mechanical treatment. Light microscopy, atomic force microscopy (AFM), powder X-Ray diffraction (PXRD), Fourier-transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA) and Zeta potential measurements were applied during this research. The carboxylated cellulose suspension of different fractions including nanofibrils, microfibrils and bundles were produced from bleached birch Kraft pulp fibers using chemical pretreatment with ammonium persulfate solution and further defibrillation using consequent mechanical treatment in a high shear laboratory mixer and ultrasonication. The characteristics of the obtained nanofibrils were: diameter 20–300 nm, crystallinity index 74.3%, Zeta potential −26.9 ± 1.8 mV, clear FTIR peak at 1740 cm−1 indicating the C=O stretching vibrations, and lower thermostability in comparison to the Kraft pulp was observed. The proposed method can be used to produce cellulose nanofibrils with defined crystallinity.
We report the manufacturing and characterization of poly (butylene succinate) (PBS) and micro cellulose (MCC) woody-like composites. These composites can be applied as a sustainable woody-like composite alternative to conventional fossil polymer-based wood-plastic composites (WPC). The PBS/MCC composites were prepared by using a melt blending of 70 wt% of MCC processed from bleached softwood. MCC was modified to enhance dispersion and compatibility by way of carbodiimide (CDI), polyhydroxy amides (PHA), alkyl ester (EST), (3-Aminopropyl) trimethoxysilane (APTMS), maleic acid anhydride (MAH), and polymeric diphenylmethane diisocyanate (PMDI). The addition of filler into PBS led to a 4.5-fold improvement of Young’s modulus E for the MCC composite, in comparison to neat PBS. The 1.6-fold increase of E was obtained for CDI modified composition in comparison to the unmodified MCC composite. At room temperature, the storage modulus E′ was found to improve by almost 4-fold for the APTMS composite. The EST composite showed a pronounced enhancement in viscoelasticity properties due to the introduction of flexible long alkyl chains in comparison to other compositions. The glass transition temperature was directly affected by the composition and its value was −15 °C for PBS, −30 °C for EST, and −10 °C for MAH composites. FTIR indicated the generation of strong bonding between the polymer and cellulose components in the composite. Scanning electron microscopy analysis evidenced the agglomeration of the MCC in the PBS/MCC composites. PMDI, APTMS, and CDI composites were characterized by the uniform dispersion of MCC particles and a decrease of polymer crystallinity. MCC chemical modification induced the enhancement of the thermal stability of MCC composites.
For reinforcing of paper, nanoparticle gels from black alder, birch and pine bark were obtained. Non-extracted bark and that extracted in biorefinery were used. For producing nanoparticles, the materials were destructed using the thermocatalytic destruction method and then dispersed in water medium in a ball mill. At a sufficient concentration, gel-like dispersions were obtained, which contained nanoparticles with the size ~300 nm. The effect of nanoparticle gels on the properties of paper sheets was investigated by introducing the dissolved gels in paper furnish and by covering both sides of paper sheets with nanoparticle gel coatings. It has been established that the nanoparticle fillers increase the tensile and burst strength. The nanoparticle fillers from extracted bark increase the mechanical indices to a higher extent. The coatings from nanoparticle gels considerably improve the Gurley air resistance of paper and increase the mechanical indices of paper sheets, especially burst strength. The effect of nanoparticle gel coatings is dependent on the coating thickness and gel concentration. The coatings decrease the tensile strength in a wet state.
Climate change makes it imperative to use materials with minimum global warming potential. The fourth-generation blowing agent HCFO-1233zd-E is one of them. The use of HCFO allows the production of polyurethane foam with low thermal conductivity. Thermal conductivity, like other foam properties, depends not only on the density but also on the cellular structure of the foam. The cellular structure, in turn, depends on the technological parameters of foam production. A comparison of pouring and spray foams of the same low density has shown that the cellular structure of spray foam consists of cells with much less sizes than pouring foam. Due to the small size of cells, spray foam has a lower radiative constituent in the foam conductivity and, as a result, a lower overall thermal conductivity than pouring foam. The water absorption of spray foam, due to the fine cellular structure, also is lower than that of pouring foam. Pouring foam with bigger cells has higher compressive strength and modulus of elasticity in the foam rise direction. On the contrary, spray foam with a fine cellular structure has higher strength and modulus in the perpendicular direction. The effect of foam aging on thermal conductivity was also studied.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.