This study is focused on stainless steel type 316L produced by selective laser melting (SLM). This steel is very resistant to corrosion in acidic environments and has extremely good strength properties at elevated temperatures. It is also characterized by a very good weldability. These properties allow for various applications of 316L in different fields. The widespread application of 316L opens up various possibilities for production of parts using SLM. Therefore, it is important to characterize the fatigue crack growth behaviour. In the present paper, the crack growth behaviour of SLM 316L stainless steel has been investigated in its as‐built condition and in different heat treatment conditions. The effect of build orientation on the crack growth path is also studied by performing fatigue crack growth tests on compact tension specimens built at 0° and 45° orientations relative to the build direction. A heat treatment above the recrystallization temperature followed by quenching is shown to create compressive residual stresses that improve the resistance against crack propagation considerably. The 45° build orientation shows crack propagation at an angle to the initial notch plane, which reveals that anisotropy still persists after heat treatment.

The application of 3D technology for fabrication of artificial porous media samples improves porous media flow studies. The geometrical characteristics of a porous media pore channel: the channel shape, size, porosity, specific surface, expansion ratio, contraction ratio, and the tortuous pathway of the channel can be controlled through advanced additive manufacturing techniques (3D printing), computed tomography imagery (CT imaging) and image analysis methods. These 3D technologies have here been applied to construct and analyze four homogeneous porous media samples with predefined geometrical properties that are otherwise impossible to construct with conventional methods. Uncertainties regarding the geometrical properties are minimized because the 3D-printed porous media samples can be evaluated with CT imaging after fabrication. It is this combination of 3D technology that improves the data acquisition and data interpretation and contributes to new insight into the phenomenon of fluid flow through porous media. The effects of the individual geometrical properties on the fluid flow are then accounted for in permeability experiments in a Hassler flow cell. The results of the experimental work are used to test the theoretical foundation of the Kozeny–Carman equation and the extended version known as the Ergun equation. These equations are developed from analogies to the Hagen–Poiseuille flow equation. Based on the results from the laboratory experiments in this study, an analytical equation based on the analytical Navier–Stokes equations is presented as an alternative to the Hagen–Poiseuille analogy for porous media channels with non-uniform channel geometries. The agreement between experiment and the new equation reveals that the dissipating losses of mechanical energy in porous media flows are not a result of frictional shear alone. The mechanical losses are also a result of pressure dissipation that arise due to the non-uniformity of the channel geometry, which induced spatial variations to the strain rate field and induce acceleration of the velocity field in the flow through the porous medium. It is this acceleration that causes a divergence from linear flow conditions as the Stokes flow criterion (Re ≪ 1) is breached and causes the convective acceleration term to affect the flow behavior. The suggested modifications of theory and the presented experiments prove that the effects of surface roughness (1) do not alter the flow behavior in the Darcy flow regime or (2) in the Forchheimer flow regime. This implies that the flow is still laminar for the Forchheimer flow velocities tested.

No abstract

No abstract

Direct Metal Deposition (DMD) is an additive manufacturing (AM) process capable of producing large components using a layer by layer deposition of molten powder. DMD is increasingly investigated due to its higher deposition rate and the possibility to produce large structural components specifically for the aerospace industry. During fabrication, a complex thermal history is experienced in different regions of the workpiece, depending on the process parameters and part geometry. The thermal history induces residual stress accumulation in the buildup, which is the main cause of distortions. In order to control the process and enhance the product quality, the understanding of the workpiece temperature is substantial. In this study, two methods to predict temperature evolution during the DMD process are introduced based on analytical and finite element methods. The objective is to compare these methods to experimental results and to provide more insights about their capabilities to predict accurately the temperature gradient, the cooling rate, and the melt pool geometry. A comparison of the computational time is also provided. Based on the results of the investigation, It appears that the analytical method provides an effective and accurate method to understand the influence of the process on the workpiece temperature.

This work analyses the texture and microstructure gradients emerging in a 316L stainless steel processed by selective laser melting, using an island scan strategy, followed by annealing. Laser processing leads to the alignment of different crystallographic directions with the build direction at the mid and top layers, as well as to gradual structural coarsening. Annealing triggers discontinuous recrystallisation at highly strained regions, such as grain boundaries and laser track centre lines, resulting in the onset of new texture gradients. The development of the mentioned texture gradients is rationalised based on a competition between thermal gradient-driven growth and epitaxial growth. GRAPHICAL ABSTRACT

No abstract

No abstract