Resumo: Este trabalho tem como objetivo verificar a cinética de cura de um pré-impregnado ("prepreg") de resina epoxídica/fibra de carbono, utilizando a técnica de calorimetria diferencial de varredura (DSC) pelo método isoconversional. O método isoconversional analisa a cinética de cura por meio da dependência da energia de ativação durante a conversão (análise isotérmica) ou temperatura (análise não-isotérmica) e utiliza esta dependência para calcular os parâmetros cinéticos. A avaliação da cinética da reação por DSC baseia-se na quantidade de calor gerado durante as reações exotérmicas. A hipótese de que o calor gerado pela reação química é proporcional à extensão da cura permite obter os parâmetros cinéticos no DSC por meio das análises pelos métodos isotérmicos e não-isotérmicos. Para o método isoconversional isotérmico, a energia de ativação média apresentou valores entre 103 e 72 kJ/mol, e, para o método isoconversional não-isotérmico um valor médio de 80,5 kJ/mol. Estes resultados foram comparados com os obtidos para os métodos ASTM E 2070 e ASTM E 698, cujos valores foram 89±5 kJ/mol e 77,5±2,5 kJ/mol, respectivamente, comprovando a eficiência do método isoconversional. Palavras-chave:Cínética de cura, compósito, resina epoxídica, DSC. Study of Cure Kinetics of a Pre-Impregnated Epoxy Resin/Carbon Fiber Using the Isoconversional MethodAbstract: This paper aims to determine the kinetics of a pre-impregnated ("prepreg") epoxy resin/carbon fiber using differential scanning calorimetry (DSC) with the isoconversional method. The latter method analyzes the cure kinetics through the dependence of activation energy during conversion (isothermal analysis) or temperature (nonisothermal analysis) and uses this dependence to calculate the kinetic parameters. The evaluation of reaction kinetics by DSC is based on the heat generating rate during an exothermic reaction. The hypothesis that a heat generated by a chemical reaction is proportional to the extension of cure allows one to obtain the kinetic parameters from the DSC curves obtained with the isothermal and nonisothermal modes. For the isoconversional isothermal method, the average activation energy ranged between 72 and 103 kJ/mol while in the non-isothermal method an average value of 80.5 kJ/mol was obtained. These results were compared with those obtained for ASTM E 2070 and ASTM E 698 methods, whose values were 89±5 kJ/mol and 77.5±2.5 kJ/mol, respectively, proving the efficiency of the method. Keywords: Cure kinetics, composite, epoxy resin, DSC. IntroduçãoA avaliação de parâmetros cinéticos a partir de dados obtidos por meio das técnicas de análises térmica tem sido um dos tópicos bastante explorados nos últimos anos gerando grande número de artigos. Vyazovkin, Rives e Schick (2010) apresentaram uma excelente revisão dos artigos publicados entre 1970 e 2010 na Thermochimica Acta, um dos principais periódicos internacionais sobre análise térmica, sendo que os mais pertinentes são ressaltados a seguir [1] . O maior impacto no campo de análise térmica cinéti...
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.