Miniscrew implants provide an excellent orthodontic anchorage. Besides the clinical benefits, miniscrew implants cause minor discomforts and in certain instances poses problematic complications. Damage to the adjacent tooth structure is the most feared complication of miniscrew implant placement, while fracture of miniscrew implants is the rarest. Miniscrew fracture could occur either during its placement or during its removal. An unusual case report is presented of a miniscrew implant tip fracture following root contact while attempting to remove it. This report highlights the effect of such miniscrew implant fracture on the dentin-pulp complex. The present case is probably the first to give direct histological evidence in humans that a miniscrew fracture or a retained miniscrew implant tip along the dentin/cementum without obvious miniscrew implant penetration could elicit pulp changes. Therefore this case report emphasizes the fact that prior to placing miniscrew implant, clinicians should have acquired proper training and adequate skills in terms of MSI placement and management of fractured MSI.

Aim: To estimate the differences in the maxillary arch morphology in buccal and palatal canine impaction in an Asian population of Gujarati origin. Methodology: An institutional ethics committee’s approval was acquired before the commencement of this study. Sixty subjects were enrolled in the study. Thirty subjects (20 females and 10 males) had a maxillary impacted canine either buccal or palatal and thirty control group participants were selected aged 13 to 18 years who sought orthodontic treatment at the tertiary health care center in Ahmedabad, Gujarat, in western India. Routine pre-treatment radiographs and dental plaster models with good anatomic details were recorded. Measurements of the inter-molar width, palatal depth, arch length, sum of the mesio-distal width of the upper incisors, and available arch space were recorded from prepared orthodontic study models using digital vernier calipers with an accuracy of 0.01 mm and brass wire. The ratio of palatal depth to inter-molar width (Ratio 1), arch length to inter-molar width (Ratio 2), and width of the maxillary incisors to available arch space (Ratio 3) were also secondarily calculated. Data were analyzed using Statistical Package for Social Sciences (SPSS) version 21, IBM Inc. The normality of the data was assessed by the Shapiro–Wilk test. As the data was found to be normally distributed, bivariate analyses were also performed (one-way ANOVA test, Bonferroni post hoc correction). The level of statistical significance was set at a p-value less than 0.05. Results: The comparison of the inter-molar width, palatal depth, arch length, sum of the mesio-distal width of the upper incisors, available arch space, Ratio 1, Ratio 2, and Ratio 3 among controls and subjects with buccal and palatal canine impaction showed overall significant differences in the inter-molar width, palatal depth, arch length, sum of the mesio-distal width of the upper incisors, and available arch space when compared using one-way ANOVA as p < 0.05. Ratios 1, 2, and 3 also showed significant differences between the buccal and palatal canine impaction. Conclusion: An inadequate arch length (p < 0.0001) and a higher degree of crowding with reduced available arch space (p < 0.0001) may be considered as early risk factors for buccal maxillary canine impaction. An inadequate inter-molar width (p < 0.0001), and an increased palatal depth (p < 0.0001) with a clinically reduced mesiodistal width of the sum of maxillary incisors may be considered as risk factors for palatal maxillary canine impaction in an Asian population of Gujarati origin.

No abstract

Currently, wide arrays of fixed functional appliances are available for the correction of Class II malocclusion. The orthodontist must choose from these appliances depending on the mechanics, efficiency, and cost of the appliance. Fixed functional appliances may reduce the individual visits and hence the cost as compared to the removable appliances. Additionally, it may save the clinician’s chair time. This report discussed the in-house laboratory fabrication and clinical procedure of customized fixed functional appliances by utilizing the readily available dental materials in the orthodontic clinical setting.

This case report was adjudged one of the best-treated cases displayed in the Indian Board of Orthodontics after the board certification process. The summary of the treatment and various records are reprinted here with minimal editing and reformatting so that the presentation resembles the actual documents submitted to the board.