Аннотация. Методами оптической и просвечивающей электронной микроскопии выполнен анализ структурно-фазовых изменений в низко-легированной стали в процессе удаления окалины. Отмечено формирование полос с повышенным содержанием перлита, обусловленное ликвацией углерода.Ключевые слова: низкоуглеродистая сталь, дислокационная субструктура, фазовый состав, пластическая деформация, окалина, плотность дис-локаций.
E-MAIL: gromov@physics.sibsiu.ruЛистовой прокат является одним из основных мате-риалов, потребляемых различными отраслями народ-ного хозяйства. В процессе горячей прокатки и охлаж-дения поверхность горячекатаной полосы вследствие окисления при взаимодействии с окружающей средой покрывается окалиной, что отрицательно сказывается на потребительских свойствах. Постоянно возрастаю-щие требования к качеству листового проката, его механическим свойствам выдвигают в число перво-очередных задач выяснение природы формирования и эволюции структурно-фазовых состояний при изго-товлении, термической обработке и удалении окали-ны [1 -3].Цель настоящей работы -выявление и анализ струк-турно-фазовых изменений в низкоуглеродистой стали в процессе удаления окалины.В качестве материала исследования использовали конструкционную сталь марки Ст08пс (0,05 -0,11 % С; 0,05 -0,17 % Si; 0,35 -0,65 % Mn; до 0,25 % Ni; до 0,1 % Cr; до 0,25 % Cu; до 0,04 % S; до 0,035 % Р; остальное железо (по массе)) [4]. Образцы стали Ст08пс для исследований вырезали из горячекатаных полос в состоянии поставки (после прокатки с темпе-ратурой начала (1250 °С) и конца (860 -890 °С) про-катки, сматывания в рулоны при температуре 670 °С и охлаж дения на воздухе до комнатной температуры) и после удаления окалины с поверхности металла сна-чала меха ническим способом (путем перегиба полосы между роликами с одновременным растяжением), а затем пропусканием через ванны с растворами серной кислоты. Исследования фазового состава и дефектной субструктуры образцов стали осуществляли методами оптической и просвечивающей дифракционной элект-ронной микроскопии ПЭМ [5, 6].В результате термомеханической обработки в ста-ли формируется поликристаллическая структура на основе α-фазы (твердый раствор на основе ОЦК крис-таллической решетки железа). Зерна α-фазы фрагмен-тированы, т.е. разделены малоугловыми границами на области преимущественно неравноосной формы (рис. 1). Относительная площадь зерна, занятая фраг-ментами, составляет примерно 0,8.Средние поперечные размеры фрагментов составля-ют 0,603 ± 0,310 мкм; интервал изменения поперечных размеров -от 0,3 до 1,5 мкм (рис. 2, а). Азимутальная Рис. 1. Электронно-микроскопическое изображение структуры стали после прокатки (стрелками указаны изгибные экстинкционные контуры)