Those parts of solid or hollow blanks whose shape is complex should be produced by means of combined radial-longitudinal extrusion. However, the use of combined extrusion processes with several degrees of flow freedom requires a preliminary assessment of shape formation, which is true, taking into consideration the peculiarities of evolution of strain sites at different stages of deformation. When deforming high blanks, the presence of an intermediate rigid zone can be observed, separating two autonomous strain sites. When constructing an estimation scheme of the initial stage of the process of combined radial-backward extrusion of hollow parts with a flange, the presence of an intermediate rigid zone is taken into consideration. The need to improve the devised estimation scheme is caused by significant deviations in the projected growths of a part from its experimentally derived dimensions. As an alternative to the axial rectangular kinematic module of the lower deformation site, the use of an axial triangular module has been proposed, whose effectiveness is demonstrated in simulating the process of radial-longitudinal extrusion with expansion. The rationality of the proposed replacement was revealed, both for forecasting the forced mode of the deformation process and for the gradual part’s shape formation. This has made it possible to reduce the projected estimates to 10 % in terms of the increase in the size of a part based on a comparative analysis with experimentally derived data. It is recommended to use the devised scheme for modeling the initial stage of the process for relatively high blanks at H0/h1>4…6; the limitation is the degeneration of the intermediate rigid zone. This will contribute to compiling recommendations for expanding the possibilities of using combined radial-backward extrusion of hollow parts with a flange during production
Калюжний В. Л., Левченко В. М., Марчук К. Л., Дементєєв М. В. Силові режими та напружено-деформований стан при холодному видавлюванні прямокутної порожнини в квадратній заготовці // Обробка матеріалів тиском. – 2019. – № 2 (49). - С. 91-97. Методом кінцевих елементів створено математичну модель і проведено аналіз холодного зворотного видавлювання прямокутної порожнини в квадратній заготовці з пластичного алюмінію Al-2024. Використана пружно-пластична модель металу. Враховано зміцнення, тертя по Кулону, швидкість деформування і тепловий ефект при холодній формозміні. Наведено моделювання процесів видавлювання, вилучення пуансона із здеформованої заготовки та виштовхування виробу з матриці. Встановлено залежності зусиль видавлювання, вилучення пуансона та виштовхування виробу від переміщення деформуючого інструменту. Визначено розподіл питомих зусиль на контактуючих поверхнях заготовки з пуансоном, матрицею і виштовхувачем. Виявлено температуру металу в процесі видавлювання. Наведено розподіл компонент напружень в здеформованій заготовці при максимальному зусиллі деформування та розподіл компонент здеформованого стану у виробі після видавлювання. З урахуванням пружної деформації визначені кінцеві форма та розміри виробу і проведено прогнозування механічних властивостей в стінках.
аспирант кафедры терапии и фармакологии graduate student of chair of therapy and pharmacology ID-автора в РИНЦ: 516725AuthorID: 516725 Ставропольский государственный аграрный университет, Ставрополь, Россия
Кротенко Г. А., Левченко В. М., Таган Л. В. Визначення енергосилових параметрів процесу видавлювання циліндричних деталей з квадратних заготовок. Oбробка матеріалів тиском. 2020. № 1 (50). С. 130-135. Проаналізовано сучасні способи отримання відносно низьких (коротких) круглих в плані заготовок для видавлювання циліндричних деталей. Показано, що вирубка з листового матеріалу навіть з використанням багаторядного розкрою не дозволяє виробляти такі заготовки із забезпеченням високого коефіцієнта використання матеріалу. Альтернативні способи, такі як різання зсувом в спеціальних штампах і розкочування, не забезпечують якість низьких заготовок або є непродуктивними. Запропоновано отримувати відносно низькі круглі в плані заготовки осадкою з квадратних, для яких величина коефіцієнта використання матеріалу наближається до 100 %. Наведено результати теоретичного аналізу процесу осадки квадратної заготовки в круглій матриці, при якій деформація характеризується вихровою течією металу. Математичну модель процесу побудовано з використанням тривимірного вихрового поля швидкостей на базі енергетичного методу. Результати розрахунків співставлено з експериментальними даними. Отримано залежності питомих сил від незаповнення для осадки квадратної заготовки, а також для стаціонарної стадії видавлювання заготовок типу стаканів з товщиною стінки 0,50 мм та 0,25 мм. Запропонована методика теоретичного аналізу може бути використана для визначення товщини стінки, при якій фестон не буде перешкодою для виготовлення тонкостінних деталей типу тюбиків. Запропоновано технологічний процес видавлювання круглої деталі (тонкостінного тюбика) з квадратної заготовки. Застосування нової технології видавлювання тюбиків з квадратних заготовок дозволяє підвищити коефіцієнт використання матеріалу з 0,67 до 0,98.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.