An experimental study was conducted to determine the heat transfer performance of advanced convective cooling techniques at the typical conditions found in a backside cooled combustion chamber. For these internal cooling channels, the Reynolds number is usually found to be above the Reynolds number range covered by available databases in the open literature. As possible candidates for an improved convective cooling configuration in terms of heat transfer augmentation and acceptable pressure drops, W-shaped and WW-shaped ribs were considered for channels with a rectangular cross section. Additionally, uniformly distributed hemispheres were investigated. Here, four different roughness spacings were studied to identify the influence on friction factors and the heat transfer enhancement. The ribs and the hemispheres were placed on one channel wall only. Pressure losses and heat transfer enhancement data for all test cases are reported. To resolve the heat transfer coefficient, a transient thermocromic liquid crystal technique was applied. Additionally, the area-averaged heat transfer coefficient on the W-shaped rib itself was observed using the so-called lumped-heat capacitance method. To gain insight into the flow field and to reveal the important flow field structures, numerical computations were conducted with the commercial code FLUENT™.
An investigation was conducted to assess the thermal performance of W-shaped, 2W-shaped and 4W-shaped ribs in a rectangular channel. The aspect ratios (W/H) were 2:1, 4:1, and 8:1. The ribs were located on one channel wall. The rib height (e) was kept constant with a rib height-to-hydraulic diameter ratio (e/Dh) of 0.02, 0.03, and 0.06. The rib pitch-to-height ratio (P/e) was 10. The Reynolds numbers investigated (Re > 90 000) are typical for combustor liner cooling configurations of gas turbines. Local heat transfer coefficients using the transient thermochromic liquid crystal technique and overall pressure losses were measured. The rib configurations were investigated numerically to visualize the flow pattern in the channel and to support the understanding of the experimental data. The results show that the highest heat transfer enhancement is obtained by rib configurations with a rib section-to-channel height ratio (Wr/H) of 1:1. W-shaped ribs achieve the highest heat transfer enhancement levels in channels with an aspect ratio of 2:1, 2W-shaped ribs in channels with an aspect ratio of 4:1 and 4W-shaped ribs in channels with an aspect ratio of 8:1. Furthermore, the pressure loss increases with increasing complexity of the rib geometry and blockage ratio.
An investigation was conducted to assess the thermal performance of 90° ribs, low and high W-shaped ribs, and combinations of low W-shaped ribs with high W-shaped ribs and with dimples in a rectangular channel with an aspect ratio (W/H) of 2:1. The blockage ratios (e/Dh) were 0.02 with the 90° ribs and the low W-shaped ribs and 0.06 with high W-shaped ribs. The rib pitch-to-height ratio (P/e) were 10 and 20. The channel height-to-dimple diameter (H/D) was 16.67; the dimple depth-to-dimple diameter (δ/D) was 0.3. The ribs and the dimples were located on one channel wall (side W). Furthermore, W-shaped ribs and 90° ribs with e/Dh = 0.027 and P/e = 10 were also individually investigated in a test channel with 1/4 of its cross section blocked. The Reynolds numbers investigated (Re > 100k) are typical for combustor liner cooling configurations in gas turbines. Local heat transfer coefficients using the transient thermochromic liquid crystal technique and overall pressure losses were measured. The different configurations were investigated numerically to visualize the flow pattern in the channel and to support the understanding of the experimental data. The results show that the highest heat transfer enhancement rates are obtained by a combination of W-shaped ribs with P/e = 10 and e/Dh = 0.06 and W-shaped ribs with P/e = 10 and e/Dh = 0.02. The best thermal performance is achieved by regularly spaced lower W-shaped ribs and by a compound roughness of regularly spaced W-shaped ribs and dimples at Re below and above 300,000, respectively.
This paper provides an overview of the ongoing development activities for the Ansaldo Energia gas turbines AE64.3A, AE94.2, AE94.2K, AE94.3A, GT26 (2006), GT26 (2011), GT36-S6 and GT36-S5. The improvements significantly reduce the energy consumption in gas turbine combined cycle (GTCC) power plants and are directed towards improved operational and fuel flexibility, increased GT power output, GT efficiency and improved component lifetime. The collaborative development, validation and application of the constant pressure sequential combustion system (‘CPSC’) for the GT36 engine will be introduced. Based on the well-established sequential burner technology as installed since 1994 on all legacy GT26 gas turbines, the operation turndown, fuel flexibility and the overall system robustness is described. The development and engine validation of the first stage burner for Improved Durability and Turndown as well as the design of a Combustor Sequential Liner within a can combustion system is shown. The reconstruction and analysis of the acoustic transfer matrix of the flame in the sequential burner together with the applied air and fuel management facilitate emission and dynamics control at both, the extremely high and low firing temperature ranges. The axial flow turbine of the GT36 heavy duty gas turbine, which has evolved from the existing and proven GT26 design, consists of an optimized annulus flow path, higher lift airfoil profiles, optimized aerodynamic matching between the turbine stages and a new and improved cooling systems of the turbine vanes and blades. A major design feature of the turbine has been to control and reduce the aerodynamic losses, associated with the airfoil profiles, trailing edges, blade tips, end walls and coolant ejection. The advantages of these design changes to the overall gas turbine efficiency have been verified via extensive experimental testing.
An investigation was conducted to assess the thermal performance of W-shaped, 2W-shaped and 4W-shaped ribs in a rectangular channel. The aspect ratios (W/H) were 2:1, 4:1 and 8:1. The ribs were located on one channel wall. The rib height (e) was kept constant with a rib height-to-hydraulic diameter ratio (e/Dh) of 0.02, 0.03 and 0.06. The rib pitch-to-height ratio (P/e) was 10. The Reynolds numbers investigated (Re>90,000) are typical for combustor liner cooling configurations of gas turbines. Local heat transfer coefficients using the transient thermochromic liquid crystal technique and overall pressure losses were measured. The rib configurations were investigated numerically to visualize the flow pattern in the channel and to support the understanding of the experimental data. The results show that the highest heat transfer enhancement is obtained by rib configurations with a rib section-to-channel height ratio (Wr/H) of 1:1. W-shaped ribs achieve the highest heat transfer enhancement levels in channels with an aspect ratio of 2:1, 2W-shaped ribs in channels with an aspect ratio of 4:1 and 4W-shaped ribs in channels with an aspect ratio of 8:1. Furthermore, the pressure loss increases with increasing complexity of the rib geometry and blockage ratio.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.