Understanding the interaction between surfaces and their surroundings is crucial in many materials-science fields, such as catalysis, corrosion, and thin-film electronics, but existing characterization methods have not been capable of fully determining the structure of surfaces during dynamic processes, such as catalytic reactions, in a reasonable time frame. We demonstrate an x-ray-diffraction-based characterization method that uses high-energy photons (85 kiloelectron volts) to provide unexpected gains in data acquisition speed by several orders of magnitude and enables structural determinations of surfaces on time scales suitable for in situ studies. We illustrate the potential of high-energy surface x-ray diffraction by determining the structure of a palladium surface in situ during catalytic carbon monoxide oxidation and follow dynamic restructuring of the surface with subsecond time resolution.

Convoluted selectivity trends and a missing link between reaction product distribution and catalyst properties hinder practical applications of the electrochemical CO2 reduction reaction (CO2RR) for multicarbon product generation. Here we employ operando X-ray absorption and X-ray diffraction methods with subsecond time resolution to unveil the surprising complexity of catalysts exposed to dynamic reaction conditions. We show that by using a pulsed reaction protocol consisting of alternating working and oxidizing potential periods that dynamically perturb catalysts derived from Cu2O nanocubes, one can decouple the effect of the ensemble of coexisting copper species on the product distribution. In particular, an optimized dynamic balance between oxidized and reduced copper surface species achieved within a narrow range of cathodic and anodic pulse durations resulted in a twofold increase in ethanol production compared with static CO2RR conditions. This work thus prepares the ground for steering catalyst selectivity through dynamically controlled structural and chemical transformations.

In this study, we have taken advantage of a pulsed CO 2 electroreduction reaction (CO 2 RR) approach to tune the product distribution at industrially relevant current densities in a gas-fed flow cell. We compared the CO 2 RR selectivity of Cu catalysts subjected to either potentiostatic conditions (fixed applied potential of −0.7 V RHE ) or pulsed electrolysis conditions (1 s pulses at oxidative potentials ranging from E an = 0.6 to 1.5 V RHE , followed by 1 s pulses at −0.7 V RHE ) and identified the main parameters responsible for the enhanced product selectivity observed in the latter case. Herein, two distinct regimes were observed: (i) for E an = 0.9 V RHE we obtained 10% enhanced C 2 product selectivity (FE C 2 H 4 = 43.6% and FE C 2 H 5 OH = 19.8%) in comparison to the potentiostatic CO 2 RR at −0.7 V RHE (FE C 2 H 4 = 40.9% and FE C 2 H 5 OH = 11%), (ii) while for E an = 1.2 V RHE , high CH 4 selectivity (FE CH 4 = 48.3% vs 0.1% at constant −0.7 V RHE ) was observed. Operando spectroscopy (XAS, SERS) and ex situ microscopy (SEM and TEM) measurements revealed that these differences in catalyst selectivity can be ascribed to structural modifications and local pH effects. The morphological reconstruction of the catalyst observed after pulsed electrolysis with E an = 0.9 V RHE , including the presence of highly defective interfaces and grain boundaries, was found to play a key role in the enhancement of the C 2 product formation. In turn, pulsed electrolysis with E an = 1.2 V RHE caused the consumption of OH – species near the catalyst surface, leading to an OH-poor environment favorable for CH 4 production.

Nanoparticle sintering during catalytic reactions is a major cause for catalyst deactivation. Understanding its atomic-scale processes and finding strategies to reduce it is of paramount scientific and economic interest. Here, we report on the composition-dependent three-dimensional restructuring of epitaxial platinum–rhodium alloy nanoparticles on alumina during carbon monoxide oxidation at 550 K and near-atmospheric pressures employing in situ high-energy grazing incidence x-ray diffraction, online mass spectrometry and a combinatorial sample design. For platinum-rich particles our results disclose a dramatic reaction-induced height increase, accompanied by a corresponding reduction of the total particle surface coverage. We find this restructuring to be progressively reduced for particles with increasing rhodium composition. We explain our observations by a carbon monoxide oxidation promoted non-classical Ostwald ripening process during which smaller particles are destabilized by the heat of reaction. Its driving force lies in the initial particle shape which features for platinum-rich particles a kinetically stabilized, low aspect ratio.

In situ high-energy surface X-ray diffraction was employed to determine the surface structure dynamics of a Pd(100) single crystal surface acting as a model catalyst to promote CO oxidation. The measurements were performed under semirealistic conditions, i.e., 100 mbar total gas pressure and 600 K sample temperature. The surface structure was studied in detail both in a steady gas flow and in a gradually changing gas composition with a time resolution of 0.5 s. The experimental technique allows for rapid reciprocal space mapping providing the complete information on structural changes of a surface with unprecedented time resolution in harsh conditions. Our results show that the (√5 × √5)R27°-PdO(101) surface oxide forms in a close to stoichiometric O 2 and CO gas mixture as the mass spectrometry indicates a transition to a highly active state with the reaction rate limited by the CO mass transfer to the Pd(100) surface. Using a low excess of O 2 in the gas stoichiometry, islands of bulk oxide grow epitaxially in the same (101) crystallographic orientation of the bulk PdO unit cell according to a Stranski−Krastanov type of growth. The morphology of the islands is analyzed quantitatively. Upon further increase of the O 2 partial pressure a polycrystalline Pd oxide forms on the surface. ■ INTRODUCTIONFor more than a century heterogeneous catalysis has been extensively exploited by the industry, and as a consequence it has been intensively studied. 1 One of the most prominent examples is the CO oxidation reaction, CO + 1 / 2 O 2 → CO 2 . This process transforms highly toxic carbon monoxide, formed e.g. as a byproduct during incomplete combustion of the fuel in internal combustion engines, to less harmful carbon dioxide gas. However, the reaction is very slow under the operational conditions in the gas phase and requires thus the presence of a solid catalysts to proceed at a sufficiently high rate. Because of its importance and relatively simple mechanism, this reaction has become the subject of numerous studies aiming to resolve the atomic-scale processes that occur on the surface of catalysts. 2 Supported nanoparticles of late transition metals represent a well-known and efficient type of oxidation catalyst and are currently widely used in catalytic converters. 3,4 Hence, a deep understanding of the fundamental processes proceeding in such systems is important for improvement of existing catalyst-based solutions and development of new potential approaches. For this purpose, studies of atomic-scale surface structure and determination of the active phase of catalysts under working conditions are essential. However, the complexity of such systems and the inability of many experimental techniques to work under realistic pressuresthe challenges known as material and pressure gapssignificantly narrow the selection of available methods for structural determination and necessitate the use of model systems. One of the commonly used approaches is to study single crystals with different surface crystallographic orientation...

No abstract

CO2 methanation over Rh/CeO2 and Ni/CeO2 highlighting the different surface speciation during reaction as deduced from our study.

Continuous exposure to methane causes IrO 2 (110) films on Ir(100) to undergo extensive reduction at temperatures from 500 to 650 K. Measurements using in situ X-ray photoelectron spectroscopy (XPS) confirm that CH 4 oxidation on IrO 2 (110) converts so-called bridging oxygen atoms (O br ) at the surface to HO br groups while concurrently removing oxygen from the oxide film. Reduction of the IrO 2 (110) film by methane is mildly activated as evidenced by an increase in the initial reduction rate as the temperature is increased from 500 to 650 K. The XPS results show that subsurface oxygen efficiently replaces O br atoms at the IrO 2 (110) surface during CH 4 oxidation, even after the reduction of multiple layers of the oxide film, and that metallic Ir gradually forms at the surface as well. The isothermal rate of IrO 2 (110) reduction by methane decreases continuously as metallic Ir replaces surface IrO 2 (110) domains, demonstrating that IrO 2 (110) is the active phase for CH 4 oxidation under the conditions studied. A key finding is that the replacement of O br atoms with oxygen from the subsurface is efficient enough to preserve IrO 2 (110) domains at the surface and enable CH 4 to reduce the ∼10-layer IrO 2 (110) films nearly to completion. In agreement with these observations, density functional theory calculations predict that oxygen atoms in the subsurface layer can replace O br atoms at rates that are comparable to or higher than the rates at which O br atoms are abstracted during CH 4 oxidation. The efficacy with which oxygen in the bulk reservoir replenishes surface oxygen atoms has implications for understanding and modeling catalytic oxidation processes promoted by IrO 2 (110).