Purpose To investigate the stability of mechanical properties during the entire shelf life of chemically‐activated bis‐acryl interim resin materials stored at ambient laboratory conditions. Materials and methods Four bis‐acryl interim resin materials with no explicit recommendation for refrigerator storage were selected (Luxatemp Plus, Visalys Temp, Structur 3, Structur Premium). Following cartridge storage at ambient laboratory conditions in 6‐month intervals, 30 specimens (2.0 × 2.0 × 25.0 mm3) were prepared in each case and stored in distilled water (37.0 ± 1.0 °C) with 3 different water storage times (2 hours, 24 hours, 7 days). Flexural strength, modulus of elasticity, modulus of toughness, and elastic recovery were determined (3‐point bend test). Data were subjected to a three‐way multivariate analysis of variance (MANOVA) to determine overall significance, followed by a series of separate one‐way ANOVAs after data were split, using Tukey and Games‐Howell post hoc tests to identify significant differences between groups (α = 0.05). Results While Luxatemp Plus showed no significant decrease for all mechanical properties during the investigated shelf life of 21 months (p > 0.05), Visalys Temp exhibited a continuous decline of the corresponding values (p < 0.05), irrespective of the water storage time. Structur 3 and Structur Premium properties remained almost unchanged during the first 6 months of the examination period. Subsequently, a progressive decrease was observed for flexural strength and modulus of elasticity, while most modulus of toughness and elastic recovery results revealed little alteration. Conclusion Depending on the bis‐acryl interim resin material, mechanical properties appeared to be susceptible to continuous degradation processes during cartridge storage at ambient conditions, especially towards the end of the material shelf life. For some materials, the chemical stabilization and recommended storage conditions should be revised by the manufacturers to prevent premature aging during shelf life.
Zusammenfassung Einf?hrung Die mechanischen Eigenschaften von abgebundenen Alginaten sollen mit der Qualit?t des Anmischens korrelieren; valide Daten dazu fehlen allerdings. Daher war es das Ziel dieser Studie, den Einfluss der Mischtechnik sowie den Erfahrungsgrad des Anmischers auf die Rei?festigkeit und die Dichte der abgebundenen Alginate zu ermitteln. Material und Methode 4 verschiedene Alginate (Cavex CA37, Zhermack Hydrogum, GC Aroma fine, Dentsply Blueprint cremix) wurden von 2 verschiedenen Behandlergruppen (Zahnarzthelferinnen, Vorkliniksstudenten) entweder per Hand oder maschinell (Cavex Alginat Mixer II) angemischt. Die angemischten Alginate wurden in einer Standardform, gem?? ISO 21563, durch einen erfahrenen Behandler platziert. Anschlie?end wurden die Dichte (Micro scale; Mettler Toledo Academica XS 205 DU) und die Rei?festigkeit (Universal Zwick Maschine 1?454; Geschwindigkeit 400?mm/min) bestimmt, nachdem die Proben (n=10 pro Gruppe) entsprechend der vom Hersteller angegebenen Mundverweildauer im Wasserbad gelagert wurden. Die statistische Auswertung zur ?berpr?fung des Einflusses des Materials, der Mischtechnik und des Behandlers erfolgte mittels parametrischer Tests (?=0,05). Ergebnisse Die Rei?festigkeitswerte lagen im Bereich von 0,45 bis 0,91?N/mm und die Dichte von 1,15 bis 1,20?g/mm3. Die maschinell angemischten Alginate zeigten eine signifikant h?here Dichte (p<0,05) und h?here Rei?festigkeiten (signifikant f?r Blueprint p<0,05). CA37 besa? die signifikant h?heren Rei?festigkeiten im Vergleich zu allen anderen getesteten Materialien (p<0,05). Die Behandlergruppe hatte dabei keinen Einfluss auf die getesteten Parameter (p>0,05). Schlussfolgerung Moderne Alginatabformmaterialien scheinen unempfindlich gegen einen Einfluss durch den Anmischenden zu sein. Dieses Ergebnis stimmt mit den Ergebnissen einer Studie ?berein. Vielmehr scheint die Auswahl des Materials von gr??erer Bedeutung zu sein, als durch wen dieses angemischt wird. Auf der anderen Seite wird die Dichte jedoch wesentlich durch die Art des Anmischens bestimmt. Maschinell angemischte Alginate sind deutlich blasenfreier und weisen eine h?here Dichte auf als manuell angemischte Alginate. Die Formgenauigkeit der Alginate ist abh?ngig vom vorhandenen Pulver-/Fl?ssigkeitsverh?ltnis. Es fehlen Daten zur Abh?ngigkeit der Formgenauigkeit von der Dichte bei einem festgelegten Pulver-/Fl?ssigkeitsverh?ltnis. Weitere Untersuchungen sind notwendig, um den Einfluss der Dichte auf andere physikalische Parameter, insbesondere auf die Formgenauigkeit zu ermitteln.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
customersupport@researchsolutions.com
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.