SynopsisThe shear viscosity material function of a highly filled suspension consisting of a Newtonian poly(butadiene acrylonitrile acrylic acid terpolymer) matrix, PBAN, mixed with an ammonium sulfate tiller at 60% by volume was studied. Both capillary and parallel disk torsional flows were employed. The rheological characterization revealed strong slip of the suspension at the walls over a broad range of shear stresses in both types of flows. The slip velocity increased approximately linearly with the shear stress. In capillary flows, above a critical shear stress, flow took place in a pluglike manner, owing to slip at the wall. The experimental findings were further elucidated to determine the slip layer thickness and the apparent shear viscosity behavior of highly filled suspensions at high shear stress at the wall values. It was concluded that the slip effects dominate the flow of highly filled suspensions and the true flow and deformation characteristics of the highly filled suspensions may be overshadowed by slip at the walls,
The rheological behavior of a very concentrated suspension (76.5 vol %), which serves as a widely used solid rocket fuel simulant, was characterized employing both torsional and capillary flows. No comprehensive studies of the rheology of concentrated suspensions have been carried out previously at such a high solids content. The suspension exhibited shear thinning over the apparent shear rate range of 3&3000 SC'. Significant slip at the wall was observed in both torsional and capillary flows with the slip velocity increasing from about 0.001 mm/s at a shear stress of 4 Pa to as high as 60 mm/s at 100 kPa. A flow visualization technique was applied for the first time to determine the wall slip velocities in torsional flow directly, to also provide the true deformation rate and feedback on yielding. The contribution of the slip of the suspension at the wall to the volumetric flow rate in capillary flow was found to increase with decreasing shear stress, giving rise to plug flow at sufficiently low shear stress values. The observed plug flow is related to the shear-thinning nature of the suspension and differs from the behavior of shear thickening suspensions, which may exhibit plug flow at high wall shear stress values, i.e., above a critical wall shear stress in capillary flow.
Composite film production based on cotton stalk xylan was studied, and the mechanical and physical properties of the films formed were investigated. Xylan and lignin were separated from cellulose by alkali extraction and, then, lignin was removed using ethanol washing. Self-supporting continuous films could not be produced using pure cotton stalk xylan. However, film formation was achieved using 8-14% (w/w) xylan without complete removal of lignin during xylan isolation. Keeping about 1% lignin in xylan (w/w) was determined to be sufficient for film formation. Films were produced by casting the film-forming solutions, followed by solvent evaporation in a temperature (20 degrees C) and relative humidity (40%) controlled environment. The elastic modulus and hypothetical coating strength of the films obtained by using 8% xylan were significantly different from the ones containing 10-14% xylan. The water vapor transfer rates (WVTR) decreased with increasing xylan concentration, which made the films thicker. The glycerol addition as an additional plasticizer resulting in more stretchable films having higher WVTR and lower water solubility values. As a result, film production was successfully achieved from xylan, which was extracted from an agricultural waste (cotton stalk), and the film-forming effect of lignin on pure xylan has been demonstrated.
Epoxy-clay nanocomposites were synthesized to examine the effects of the content and type of different clays on the structure and mechanical properties of the nanocomposites. Diglycidyl ether of bisphenol-A (epoxy) was reinforced by 0.5-11 wt % natural (Cloisite Na ϩ ) and organically modified (Cloisite 30B) types of montmorillonite. SEM results showed that as the clay content increased, larger agglomerates of clay were present. Nanocomposites with Cloisite 30B exhibited better dispersion and a lower degree of agglomeration than nanocomposites with Cloisite Na ϩ . X-ray results indicated that in nanocomposites with 3 wt % Cloisite 30B, d-spacing expanded from 18.4 Å (the initial value of the pure clay) to 38.2 Å. The glass transition temperature increased from 73°C, in the unfilled epoxy resin, to 83.5°C in the nanocomposite with 9 wt % Cloisite 30B. The tensile strength exhibited a maximum at 1 wt % modified clay loading. Addition of 0.5 wt % organically modified clay improved the impact strength of the epoxy resin by 137%; in contrast, addition of 0.5 wt % unmodified clay improved the impact strength by 72%. Tensile modulus increased with increasing clay loading in both types of nanocomposites.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.