Accurately replicating and analyzing cellular responses to mechanical cues is vital for exploring metastatic disease progression. However, many of the existing in vitro platforms for applying mechanical stimulation seed cells on synthetic substrates. To better recapitulate physiological conditions, a novel actuating platform is developed with the ability to apply tensile strain on cells at various amplitudes and frequencies in a high‐throughput multi‐well culture plate using a physiologically relevant substrate. Suspending fibrillar fibronectin across the body of the magnetic actuator provides a matrix representative of early metastasis for 3D cell culture that is not reliant on a synthetic substrate. This platform enables the culturing and analysis of various cell types in an environment that mimics the dynamic stretching of lung tissue during normal respiration. Metabolic activity, YAP activation, and morphology of breast cancer cells are analyzed within one week of cyclic stretching or static culture. Further, matrix degradation is significantly reduced in breast cancer cell lines with metastatic potential after actuation. These new findings demonstrate a clear suppressive cellular response due to cyclic stretching that has implications for a mechanical role in the dormancy and reactivation of disseminated breast cancer cells to macrometastases.

<div class="section abstract"><div class="htmlview paragraph">Automated fiber placement of pre-impregnated (pre-preg), thermoset carbon materials has been industrialized for decades whereas dry-fiber carbon materials have only been produced at relatively low rates or volumes for large aerospace structures. This paper explores the differences found when processing dry-fiber, thermoset, carbon materials (DFP) as compared to processing pre-preg, thermoset materials with Automated Fiber Placement (AFP) equipment at high rates. Changes to the equipment are required when converting from pre-preg to dry fiber material processing. Specifically, the heating systems, head controls, and tow tension control all must be enhanced when transitioning to DFP processes. Although these new enhancements also require changes in safety measures, the changes are relatively small for high performance systems.</div><div class="htmlview paragraph">Processing dry fiber material requires a higher level of heating, tension control and added safety measures. However, once these are achieved, processing rates and reliability may be significantly improved for DFP versus traditional pre-preg AFP processing. Overall payout speeds as well as steering speeds can be increased for dry fiber resulting in increased laydown rates when using current AFP processing techniques. The lack of resin within the material greatly reduces resin build-up, which supports longer maintenance intervals and greater reliability by minimizing or eliminating the problems associated with resin build-up. The controlled emission area and fast response time of precision heating systems greatly reduce unwanted heat on surrounding areas and increase process performance. In addition to DFP, further developments in the heating system have also proved beneficial for thermoset as well as thermoplastic processing. All of these advantages increase the machine utilization as well as reliability when processing aerospace parts made from dry fiber materials with AFP equipment.</div></div>

Heat stress (HS) decreases lactation output in sows due to an attempt to reduce metabolic heat production. However, this negatively affects litter growth performance. Therefore, the study objective was to determine whether electronically controlled cooling pads (ECP) would improve indirect measures of lactation output (e.g., total heat production; THP) and litter growth performance in HS exposed sows. Over two repetitions, 12 multiparous (2.69 ± 0.85) lactating sows [265.4 ± 26.1 kg body weight (BW)] and litters were assigned to either an ECP (n = 3/repetition) or a non-functional ECP (NECP; n = 3/repetition) and placed into farrowing crates within indirect calorimeters from d 3.7 ± 0.5 to d 18.7 ± 0.5 of lactation. Litters were standardized across all sows (11.4 ± 0.7 piglets/litter), and sows were provided ad libitum feed and water. All sows were exposed to cyclical HS (28.27 ± 0.26°C nighttime to 33.09 ± 0.19°C daytime). On d 4, 8, 14, and 18 of lactation, indirect calorimetry was performed on each individual sow and litter to determine THP and THP/kg BW 0.75. Body temperature (TB) was measured hourly using vaginal implants, and respiration rate [RR; breaths per minute (bpm)] was measured daily at 0700, 1100, 1300, 1500, and 1900 hrs. Sow feed intake (FI) was assessed daily. Litter weights were obtained at birth, on d 4, 8, 14, and 18 of lactation, and at weaning. Data were analyzed using PROC GLIMMIX with sow and/or litter as the experimental unit. An overall decrease (P &lt; 0.01; 25 bpm) in RR and maximum daily TB (P = 0.02; 0.40°C) was observed in ECP versus NECP sows. An increase in THP (P &lt; 0.01; 20.4%) and THP/kg BW 0.75 (P &lt; 0.01; 23.1%) was observed for ECP when compared to NECP sows and litters. Litter average daily gain and weaning weight was increased (P &lt; 0.05; 25.0 and 19.2%, respectively) for ECP versus NECP litters. No FI differences were observed (P = 0.40) when comparing ECP (5.66 ± 0.31 kg/d) and NECP (5.28 ± 0.31 kg/d) sows. In summary, ECPs improve litter growth, thermoregulatory measures, and bioenergetic parameters associated with greater milk production in lactating sows exposed to cyclical HS.

No abstract

This study was designed to evaluate the effects of electronically-controlled floor cooling pads on thermoregulatory and reproductive parameters in boars during heat stress (HS). Boars (n = 24) were randomly assigned to crates with non-functional pads (CON) or pads that were flushed in either 8-min intervals or when the pad reached 28.5°C (FLUSH). For 3 d, boars were subjected to cyclical HS (28 to 35°C; &gt;65% relative humidity). Boars were fed 2.4 kg/d and daily feed intake was recorded. Respiration rate (RR), rectal temperature (Rtemp) and skin temperature were recorded every 2 h during HS (via IR camera), testicular temperature was recorded twice daily. Semen was collected d7 and d14 before HS, the day following HS and weekly for 6 weeks and evaluated for volume, sperm concentration, motility, progressive motility, morphological abnormalities, and viability. After 2 h of HS, FLUSH boars had reduced RR (P &lt; 0.001) and RTemp (P &lt; 0.001) when compared to control boars, and this difference was maintained throughout HS. Skin and testicular temperature were reduced in FLUSH vs. CON boars after 6 h of HS (P &lt; 0.05). Semen volume was greater in FLUSH vs CON boars (P = 0.01) resulting in a tendency for an increase in total sperm per ejaculate (P = 0.075). From weeks 2 to 5 post-HS, FLUSH boars had increased motility (P = 0.006) and progressive motility (P = 0.001), with corresponding increases in sperm kinematic motion parameters when compared to CON boars. The number of morphologically normal sperm cells were increased (P = 0.006) in FLUSH vs CON boars due to reduced distal droplets (P = 0.033) and proximal droplets (P &lt; 0.001). Abnormal acrosomes were reduced (P &lt; 0.001) in FLUSH vs CON boars at week 3 post-HS. In summary, electronically controlled cooling pads effectively reduced negative thermoregulatory indicators of HS and minimized or removed the negative impacts of HS on semen quality in boars.

No abstract

No abstract

No abstract