Light emitting diode (LED) lighting is becoming more and more popular, as incandescent lamps are being phased out globally. LEDs have several advantages over incandescent lamps, including energy efficiency, robustness, long lifetime, and good temporal stability. The three latter features make LEDs attractive candidates as new photometric standards. Because the spectra of white LEDs are limited to the visible wavelength range, a novel method for the realization of photometric units based on the predictable quantum efficient detector (PQED) can be utilized. The method eliminates the need of photometric filters that are traditionally used in photometry, and instead relies on carrying out the photometric weighting numerically based on the measured relative spectrum of the source. The PQED-based realization simplifies the traceability chain of photometric measurements significantly as compared with the traditional filter-based method. The measured illuminance values of a white LED deviate by only 0.03% when determined by the new and the traditional methods. The new PQED method has significantly lower expanded uncertainty of 0.26% (k 5 2) as compared with that of the traditional filter-based method of 0.42% (k 5 2). Furthermore, when filtered photometers that measure LED lighting are calibrated using LED lamps as calibration sources instead of incandescent lamps, a significant decrease in the uncertainty related to the spectral mismatch correction can be obtained. The maximum spectral mismatch errors of LED measurements decreased on average by a factor of 3 when switching from an incandescent lamp to an LED calibration source.

General lighting is undergoing a revolutionary change towards LED-based technologies. To provide firm scientific basis for the related colorimetric and photometric measurements, this paper presents the development of new white-LED-based illuminants for colorimetry, and their evaluation to recommend a new reference spectrum for calibration of photometers. Spectra of 1516 LED products were measured and used to calculate eight representative spectral power distributions for LED sources of different correlated colour temperature categories. The suitability of the calculated representative spectra for photometer calibration was studied by comparing average spectral mismatch errors with CIE Standard Illuminant A, which has been used for decades as the reference spectrum for incandescent standard lamps in calibration of photometers. It was found that in general, when compared with Standard Illuminant A, all the potential LED calibration spectra reduced spectral mismatch errors when measuring LED products. Out of the potential LED calibration spectra tested, the white LED spectrum with correlated colour temperature of 4103 K was found to be the most suitable candidate to complement Standard Illuminant A in luminous responsivity calibrations of photometers. When compared with Standard Illuminant A, employing the 4103 K reference spectrum reduced the spectral mismatch errors, on average, by approximately a factor of two in measurements of LED products and lighting. Furthermore, the new LED reference spectrum was found to reduce the spectral mismatch errors in measurements of daylight, and many types of fluorescent and discharge lamps, indicating that the proposed reference spectrum is a viable alternative to Standard Illuminant A for calibration of photometers.

The production of incandescent light bulbs is bound to end, as incandescent lighting is being phased out globally in favour of more energy-efficient and sustainable solutions. Temporally stable light-emitting diodes (LEDs) are potential candidates to replace incandescent lamps as photometric source standards. However, traditional V(λ) filter based photometers may have large uncertainty when LEDs are measured instead of incandescent lamps. This is due to the narrow and complicated spectra of LEDs. When the spectra of LEDs are limited to the visible wavelength range, new silicon detector technology can be advantageously exploited in photometry. We present a novel method—based on the recently introduced Predictable Quantum Efficient Detector (PQED)—for the realization of photometric units which completely eliminates the need to use V(λ) filters. Instead, the photometric weighting is taken into account numerically by measuring the relative spectral irradiance. The illuminance values of a blue and a red LED were determined using the new method and a conventional reference photometer. The values obtained by the two methods deviated from each other by −0.06% and 0.48% for the blue and red LED, respectively. The PQED-based values have much lower standard uncertainty (0.17% to 0.18%) than the uncertainty of the values based on the conventional photometer (0.46% to 0.51%).

We have developed spectral models describing the electroluminescence spectra of AlGaInP and InGaN light-emitting diodes (LEDs) consisting of the Maxwell-Boltzmann distribution and the effective joint density of states. One spectrum at a known temperature for one LED specimen is needed for calibrating the model parameters of each LED type. Then, the model can be used for determining the junction temperature optically from the spectral measurement, because the junction temperature is one of the free parameters. We validated the models using, in total, 53 spectra of three red AlGaInP LED specimens and 72 spectra of three blue InGaN LED specimens measured at various current levels and temperatures between 303 K and 398 K. For all the spectra of red LEDs, the standard deviation between the modelled and measured junction temperatures was only 2.4 K. InGaN LEDs have a more complex effective joint density of states. For the blue LEDs, the corresponding standard deviation was 11.2 K, but it decreased to 3.5 K when each LED specimen was calibrated separately. The method of determining junction temperature was further tested on white InGaN LEDs with luminophore coating and LED lamps. The average standard deviation was 8 K for white InGaN LED types. We have six years of ageing data available for a set of LED lamps and we estimated the junction temperatures of these lamps with respect to their ageing times. It was found that the LEDs operating at higher junction temperatures were frequently more damaged.