A hundred years on, the energy-intensive Haber-Bosch process continues to turn the N in air into fertilizer, nourishing billions of people while causing pollution and greenhouse gas emissions. The urgency of mitigating climate change motivates society to progress toward a more sustainable method for fixing N that is based on clean energy. Surface oxygen vacancies (surface O ) hold great potential for N adsorption and activation, but introducing O on the very surface without affecting bulk properties remains a great challenge. Fine tuning of the surface O by atomic layer deposition is described, forming a thin amorphous TiO layer on plasmon-enhanced rutile TiO /Au nanorods. Surface O in the outer amorphous TiO thin layer promote the adsorption and activation of N , which facilitates N reduction to ammonia by excited electrons from ultraviolet-light-driven TiO and visible-light-driven Au surface plasmons. The findings offer a new approach to N photofixation under ambient conditions (that is, room temperature and atmospheric pressure).

This paper describes the production of syngas from photocatalytic CO2 reduction with a tunable CO/H2 ratio via adjusting the properties of CuPt alloy and the distribution of cocatalysts on TiO2 hollow spheres.

Silicon is a promising photocathode material in photoelectrochemical water splitting for hydrogen production, but it is primarily limited by photocorrosion in aqueous electrolytes. As an extensively used protective material, crystalline TiO2 could protect Si photoelectrode against corrosion. However, a large number of grain boundaries (GBs) in polycrystalline TiO2 would induce excessive recombination centers, impeding the carrier transport. This paper describes the introduction of oxygen vacancies (Ovac) with controllable spatial distribution for GBs to promote carrier transport. Two kinds of Ovac distribution, Ovac along GBs and Ovac inside grains, are compared, where the latter one is demonstrated to facilitate carrier transport owing to the formation of tunneling paths across GBs. Consequently, a simple p‐Si/TiO2/Pt heterojunction photocathode with controllable Ovac distribution in TiO2 shows a +400 mV onset potential shift and yields an applied bias photon‐to‐current efficiency of 5.9 %, which is the best efficiency reported among silicon photocathodes except for silicon homojunction.

Copper (Cu) can efficiently catalyze the electrochemical CO2 reduction reaction (CO2RR) to produce value-added fuels and chemicals, among which methane (CH4) has drawn attention due to its high mass energy density. However, the linear scaling relationship between the adsorption energies of *CO and *CH x O on Cu restricts the selectivity toward CH4. Alloying a secondary metal in Cu provides a new freedom to break the linear scaling relationship, thus regulating the product distribution. This paper describes a controllable electrodeposition approach to alloying Cu with oxophilic metal (M) to steer the reaction pathway toward CH4. The optimized La5Cu95 electrocatalyst exhibits a CH4 Faradaic efficiency of 64.5%, with the partial current density of 193.5 mA cm–2. The introduction of oxophilic La could lower the energy barrier for *CO hydrogenation to *CH x O by strengthening the M–O bond, which would also promote the breakage of the C–O bond in *CH3O for the formation of CH4. This work provides a new avenue for the design of Cu-based electrocatalysts to achieve high selectivity in CO2RR through the modulation of the adsorption behaviors of key intermediates.

The mechanism of how interfacial wettability impacts the CO2 electroreduction pathways to ethylene and ethanol remains unclear. This paper describes the design and realization of controllable equilibrium of kinetic-controlled *CO and *H via modifying alkanethiols with different alkyl chain lengths to reveal its contribution to ethylene and ethanol pathways. Characterization and simulation reveal that the mass transport of CO2 and H2O is related with interfacial wettability, which may result in the variation of kinetic-controlled *CO and *H ratio, which affects ethylene and ethanol pathways. Through modulating the hydrophilic interface to superhydrophobic interface, the reaction limitation shifts from insufficient supply of kinetic-controlled *CO to that of *H. The ethanol to ethylene ratio can be continuously tailored in a wide range from 0.9 to 1.92, with remarkable Faradaic efficiencies toward ethanol and multi-carbon (C2+) products up to 53.7% and 86.1%, respectively. A C2+ Faradaic efficiency of 80.3% can be achieved with a high C2+ partial current density of 321 mA cm−2, which is among the highest selectivity at such current densities.

A hundred years on, the energy‐intensive Haber–Bosch process continues to turn the N2 in air into fertilizer, nourishing billions of people while causing pollution and greenhouse gas emissions. The urgency of mitigating climate change motivates society to progress toward a more sustainable method for fixing N2 that is based on clean energy. Surface oxygen vacancies (surface Ovac) hold great potential for N2 adsorption and activation, but introducing Ovac on the very surface without affecting bulk properties remains a great challenge. Fine tuning of the surface Ovac by atomic layer deposition is described, forming a thin amorphous TiO2 layer on plasmon‐enhanced rutile TiO2/Au nanorods. Surface Ovac in the outer amorphous TiO2 thin layer promote the adsorption and activation of N2, which facilitates N2 reduction to ammonia by excited electrons from ultraviolet‐light‐driven TiO2 and visible‐light‐driven Au surface plasmons. The findings offer a new approach to N2 photofixation under ambient conditions (that is, room temperature and atmospheric pressure).

The reduction of carbon dioxide using electrochemical cells is an appealing technology to store renewable electricity in a chemical form. The preferential adsorption of oxygen over carbon atoms of intermediates could improve the methanol selectivity due to the retention of C–O bond. However, the adsorbent-surface interaction is mainly related to the d states of transition metals in catalysts, thus it is difficult to promote the formation of oxygen-bound intermediates without affecting the carbon affinity. This paper describes the construction of a molybdenum-based metal carbide catalyst that promotes the formation and adsorption of oxygen-bound intermediates, where the sp states in catalyst are enabled to participate in the bonding of intermediates. A high Faradaic efficiency of 80.4% for methanol is achieved at −1.1 V vs. the standard hydrogen electrode.

Protective layers are essential for Si-based photocathodes to achieve long-term stability. The conventionally used inorganic protective layers, such as TiO2, need to be free of pinholes to isolate Si from corrosive solution, which demands extremely high-quality deposition techniques. On the other hand, organic hydrophobic protective layers suffer from the trade-off between current density and stability. This paper describes the design and fabrication of a discontinuous hybrid organic protective layer with controllable surface wettability. The underlying hydrophobic layer induces the formation of thin gas layers at the discontinuous pores to isolate the electrolyte from Si substrate, while allowing Pt co-catalyst to contact the electrolyte for water splitting. Meanwhile, the surface of this organic layer is modified with hydrophilic hydroxyl groups to facilitate bubble detachment. The optimized photocathode achieves a stable photocurrent of 35 mA/cm2 for over 110 h with no trend of decay.