The paper presents a conceptual design of a 10 MW multipurpose nuclear research reactor (MPRR) loaded with the low-enriched uranium (LEU) VVR-KN fuel type. Neutronics and burnup calculations have been performed using the REBUS-MCNP6 linkage system code and the ENDF/B-VII.0 data library. The core consists of 36 fuel assemblies: 27 standard fuel assemblies and 9 control fuel assemblies with the uranium density of 2.8 gU/cm3 and the 235U enrichment of 19.75 wt.%. The cycle length of the core is 86 effective full-power days with the excess reactivity of 9600 and 1039 pcm at the beginning of cycle and the end of cycle, respectively. The highest power rate and the highest discharged burnup of fuel assembly are 393.49 kW and 56.74% loss of 235U, respectively. Thermal hydraulics analysis has also been conducted using the PLTEMP4.2 code for evaluating the safety parameters at a steady state of the hottest channel. The maximum temperatures of coolant and fuel cladding are 66.0°C and 83.0°C, respectively. This value is lower than the design limit of 98°C for cladding temperature. Thermal fluxes at the vertical irradiation channels and the horizontal beam ports have been evaluated. The maximum thermal fluxes of 2.5 × 1014 and 8.9 ×1013 n·cm−2·s−1 are found at the neutron trap and the beryllium reflector, respectively.

This paper presents results of steady-state thermal-hydraulic analysis for the designed working core of the Dalat Nuclear Research Reactor (DNRR) using the PLTEMP/ANL code. The core was designed to be loaded with 92 low-enriched uranium (LEU) VVR-M2 fuel bundles (FBs) and 12 beryllium rods surrounding a neutron trap at the core center, for replacement of the previous core with 104 high-enriched uranium (HEU) VVR-M2 FBs. Before using this code for thermohydraulic analysis of the designed LEU working core, it was validated by comparing calculation results with experimental data collected from the HEU working core of the DNRR. The discrepancy between calculated results and measured data was at the maximum about 0.8°C and 1.5°C of fuel cladding and outlet coolant temperatures, respectively. In the design calculation, thermohydraulic safety was confirmed through evaluation of the fuel cladding and coolant temperatures, as well as of other safety parameters such as Departure from Nucleate Boiling Ratio (DNBR) and Onset of Nucleate Boiling Ratio (ONBR). The calculation results showed that, in normal operation conditions at full nominal thermal power of 500 kW without uncertainty parameters, the maximum fuel cladding temperature of the hottest FB was about 90.4°C, which is lower than its limit value of 103°C, the minimum DNBR was 32.0, which is much higher than the recommended value of 1.5, and the minimum ONBR was 1.43, which is higher than the recommended value of 1.4 for VVR-M2 LEU fuel type. When the global and local hot channel factors were taken into account, the maximum temperature of fuel cladding at the hottest FB was about 98.4 °C, for global only, and 114.3°C, for global together with local hot channel factors. The calculation results confirm the safety operation of the designed LEU core loaded with 92 fresh VVR-M2 FBs.

Radiation safety analysis of a new interim storage of the Dalat Nuclear Research Reactor (DNRR) for keeping spent high enriched uranium (HEU) fuel bundles during the core conversion to low enriched uranium (LEU) fuel had been performed and presented. The photon source and decay heat of the spent HEU fuel bundles were calculated using the ORIGEN2.1 code. Gamma dose rates of the spent fuel interim storage were evaluated using the MCNP5 code with various scenarios of water levels in the reactor tank and cooling time. The radiation safety analysis shows that the retention of 106 spent HEU fuel bundles at the interim storage together with a core of 92 LEU fuel bundles meets the requirements of radiation safety. The results indicate that in the most severe case, i.e., the complete loss of water in the reactor tank, the operators still can access the reactor hall to mitigate the accident within a limited time. Particularly, in the control room, the dose rate of about 1.4  μ Sv / h is small enough for people to work normally.

This report presents the methods and calculated results of the activity inventory in the structural components of the Dalat Nuclear Research Reactor (DNRR). These components include the shielding concrete, the reactor tank, and its inside irradiated facilities; the thermal and thermalizing columns; and the horizontal channels. The MCNP5 code with a three-dimensional neutron transport model was used to calculate the neutron flux distribution, neutron energy spectrum at different locations, and activation cross sections of long-lived radioactive nuclides in activated major materials, including heavy concrete, reflection graphite, and aluminum of the reactor. The calculated results of the energy spectrum and activation cross sections of MCNP5 were used in the ORIGEN2.1 point depletion code to calculate the neutron-induced activity of activated materials at different time points by modeling the irradiation history and radioactive decay. Radioactivity of long-lived key activation products such as 41Ca, 60Co, 55Fe, 63Ni, and 152Eu was modeled, and volumes of radioactive waste mainly of ordinary concrete, graphite, and aluminum in the structural components of the reactor were estimated. Experimental results of neutron flux and specific activities of some typical nuclides such as 60Co, 152Eu, 55Fe, and 63Ni in activated aluminum samples showed good agreement with the calculated results. As part of the national regulation requirements, the obtained data have been used to develop the decommissioning plan for the operational DNRR, with an estimation of about 10 years before its permanent shutdown.