The publication research task is related to one of the solution aspects in reference to decarbonization of transport by transferring the operation of diesel engines to natural gas. The results of converted diesel engines into operation with dual-fuel (D-NG) without significant constructive modifications are focused on forecasting the energy efficiency parameters of in-service engine models and evaluation of the reserves improvement. This paper presents energy efficiency parameters and characteristics of the combustion cycle methodological optimization of high-speed 79.5/95.5 mm diesel engine with a conventional fuel injection system. Interrelations between the indicated efficiency (ηi), combustion cycle performance parameters (excess air ratio (α), compression ratio (ε), degree of pressure increase in the cylinder (λ), maximum cycle pressure (pmax), air pressure (pk), air temperature (Tk) after compression, etc.), and heat release characteristics were determined and researched. Directions of the optimization when the engines were operating in a wide range of load (pmi) modes were also obtained: the low energy efficiency in the low-load mode were due to reduced heat release dynamics (combustion time increased up to 200° CA). The main influencing factors for ηi were the pilot-injection portion phase (φinj) and α, optimization of ε was inefficient. To avoid exceeding the permissible limits of reliability for pmax, the realized reserve of ηi increase was estimated as 10%. Methodological tools for the practical application of parametric analysis to the conversion of diesel to dual-fuel operation have been developed and adapted in the form of a numerical modeling algorithm, which was presented in nomogram form. For improvement of initial energy parameters for a specific engine models heat release characteristics identification, accurate methods must be used. The proposed methodology is seen as a theoretical tool for a dual-fuel conversion models for in-service engines and has benefit of a practical use of a fast application in the industrial field.

The publication examines one of the most effective ways to decarbonize marine transport, specifically the secondary heat sources utilization in the cogeneration cycle of the main engines. The research focuses on the optimization of Organic Rankine Cycle (ORC) performance parameters by combining them with the exhaust energy potential of a medium speed four-stroke main diesel engine in ISO8178 (E3) load cycle modes. Significant advantages were not found between the evaluated Wet-, Isentropic-, and Dry-type liquids (R134a, R141b, R142b, R245fa, Isopentane) in terms of ORC energy performance with a 10% difference. The use of a variable geometry turbogenerator turbine with Dry-type (R134a) working fluid is characterized by the highest ORC energy efficiency up to 15% and an increase in power plant (including turbogenerator generated mechanical) by 6.2%. For a fixed geometry turbine, a rational control strategy of the working fluid flow (Gd.sk − πT) is determined by the priorities of the power plant in certain load modes. The influence of the overboard water temperature on the ORC energy indicators does not exceed ±1%; however, it influences the thermodynamic saturation parameters of the working fluid condensation and, in connection with that, the fluid selection.

No abstract

According to the International Council on Combustion Engines (CIMAC) and International Maritime Organization (IMO) statistics, the rational selection of Marine Bunker Fuel (MBF) properties is an effective way to improve operating conditions and energy efficiency of all types of marine Diesel Engines (DEs). The publication presents the results of studies on the influence of heavy and distillate MBF properties on the characteristics of different DE types: high-speed (Caterpillar 3512B, MTU 8V 396TB), medium-speed (SKL VDS 48/42, ChN 26.5/31) ir low-speed (MAN B&W 6S60MC). The aim of work is to form a methodological framework for assessing the influence of marine fuel properties on the energy performance of different types of ship power plants. Numerical methods show that in the case of unfavourable selection of the density and viscosity of marine fuels regulated by the standard ISO 8217:2017, the changes in specific fuel consumption be reach up to 10% low-speed, 4…7% medium-speed, and 2…3% high-speed DEs. As the density varies from light grades to 1010 kg/m3, the change in be is 3…4%. At low viscosity, as the density increases to 1030 kg/m3, the low-speed engine comparative fuel consumption increases by 5%. It is recommended not to use fuel with a density >1010 kg/m3 and a viscosity <300…400 mm2/s. Developed solutions for the rational selection of bunkered marine fuel properties for a specific DE model trough the influence of density and viscosity on fuel injection and combustion characteristics based on multiparametric diagrams of relative fuel consumption change.

CO2 emissions from international shipping could increase between 50-250% by 2050 year. The EEDI (Energy Efficiency Design Index) is a key requirement for regulating CO2 emissions of maritime transport; a requirement was introduced in 2011 by the International Maritime Organization and came into force gradually. In recent studies it was investigated that no other technologies has the potential and reserves compared to Cogeneration systems. The article provides a short review of ship energy efficiency design index improving technologies and cogeneration systems application for maritime transport. A brief comparative analysis of cogeneration cycles is provided also. CO2 emissions from international shipping could increase between 50–250% by 2050 year. The EEDI (Energy Efficiency Design Index) is a key requirement for regulating CO2 emissions of maritime transport; a requirement was introduced in 2011 by the International Maritime Organization and came into force gradually. In recent studies it was investigated that no other technologies have the potential and reserves compared to Cogeneration systems. The article provides a short review of ship energy efficiency design index improving technologies and cogeneration systems application for maritime transport which have direct relation with CO2 emissions. A brief comparative analysis of cogeneration cycles is provided also.