Controlled on-surface film growth of porous and crystalline frameworks is a central prerequisite for incorporating these materials into functional platforms and operational devices. Here, we present the synthesis of thin zirconium-based metal-organic framework (MOF) films by vapor-assisted conversion (VAC). We established protocols adequate for the growth of UiO-66, UiO-66(NH), UiO-67, and UiO-68(NH) as well as the porous interpenetrated Zr-organic framework, PPPP-PIZOF-1, as highly oriented thin films. Through the VAC approach, precursors in a cast solution layer on a bare gold surface are reacting to form a porous continuous MOF film, oriented along the [111] crystal axis, by exposure to a solvent vapor at elevated temperature of 100 °C and 3 h reaction time. It was found that the concentration of dicarboxylic acid, the modulator, the droplet volume, and the reaction time are vital parameters to be controlled for obtaining oriented MOF films. Using VAC for the MOF film growth on gold surfaces modified with thiol SAMs and on a bare silicon surface yielded oriented MOF films, rendering the VAC process robust toward chemical surface variations. Ethanol sorption experiments show that a substantial part of the material pores is accessible. Thereby, the practical VAC method is an important addition to the toolbox of synthesis methods for thin MOF films. We expect that the VAC approach will open new horizons in the formation of highly defined functional thin MOF films for numerous applications.

A Zr-based MOF of the PIZOF type, which consists of two independent and mutually interpenetrating UiO-type frameworks with [ZrO(OH)(OC)] nodes, does not only form with a PEPEP dicarboxylic acid (P = phenylene, E = ethynylene). Also dicarboxylic acids with the shorter PPPP and PEPP spacers were found to give PIZOFs, denoted PPPP-PIZOF and PEPP-PIZOF, respectively. Reducing the spacer length even further to a PEEP segment caused a switchover to the formation of a UiO framework. The hysteresis in the Ar sorption curve of PEPP-PIZOF-1 and the slightly too large amount of combustion residue from PPPP-PIZOF-1 suggest structural defects. These hint at a mismatch between the requirement of the optimal linker length for PIZOF formation and the lengths of the PEPP and PPPP dicarboxylates. Nevertheless, these dicarboxylates prefer the formation of a PIZOF over the formation of a UiO structure. PEPEP-PIZOF-2, PPPP-PIZOF-1, and PEPP-PIZOF-1 are stable in air up to 325, 350, and 300 °C, respectively, and have BET surface areas of 2350, 2020, and 1650 m g, respectively. PEPEP-PIZOFs, even those with very hydrophilic oligo(ethylene glycol) side chains on the linkers, are very stable in water and also during drying from a water-wetted state. On the contrary, PEPP-PIZOF-1 and PPPP-PIZOF-1 that had been exposed to water required exchange of water for ethanol before drying to mostly preserve the framework. The results emphasize the importance of differentiating between framework damage caused through hydrolysis in water and through drying from a water-wetted state. The sensitivity of PEPP-PIZOF-1 and PPPP-PIZOF-1 against drying from a water-wetted state may be the consequence of defects. The drying stability of water-wetted PEPEP-PIZOFs lets us suggest that reversible bending of the linkers contributes to the stability of the PEPEP-PIZOFs.

The synthesis and characterization of a chemiluminescent metal–organic framework with high porosity is reported. It consists of Zr6O6(OH)4 nodes connected by 4,4′‐(anthracene‐9,10‐diyl)dibenzoate as the linker and luminophore. It shows the topology known for UiO‐66 and is therefore denoted PAP‐UiO. The MOF was not only obtained as bulk material but also as a thin film. Exposure of PAP‐UiO as bulk or film to a mixture of bis‐(2,4,6‐trichlorophenyl) oxalate, hydrogen peroxide, and sodium salicylate in a mixture of dimethyl and dibutyl phthalate evoked strong and long lasting chemiluminescence of the PAP‐UiO crystals. Time dependent fluorescence spectroscopy on bulk PAP‐UiO and, for comparison, on dimethyl 4,4′‐(anthracene‐9,10‐diyl)dibenzoate provided evidence that the chemiluminescence originates from luminophores being part of the PAP‐UiO, including the luminophores inside the crystals.

Postsynthetic modification of metal-organic frameworks is an important method to tailor their properties. We report on the nitrile oxide-alkyne cycloaddition (NOAC) as a modification tool, a reaction requiring neither strained alkynes nor a catalyst. This is demonstrated with the reaction of nitrile oxides with PEPEP-PIZOF-15 and -19 at room temperature. PIZOF-15 and -19 are porous Zr-based MOFs (BET surface areas 1740 and 960 m g, respectively) consisting of two mutually interpenetrating UiO-type frameworks with linkers of the type OC[PE-P(R,R)-EP]CO (P, phenylene; E, ethynylene; R and R, side chains at the central benzene ring with R = R = OCHC≡CH or R = OCHC≡CH and R = O(CHCHO)Me). Their syntheses, using benzoic acid as a modulator, and their characterization are reported herein. The propargyloxy (OCHC≡CH) side chains contain the ethyne moieties needed for NOAC. Formation of nitrile oxides through oxidation of oximes in aqueous ethanolic solution in the presence of PEPEP-PIZOF-15 and -19 resulted in the reaction of 96-100% of the ethyne moieties to give isoxazoles. Thereby the framework was preserved. The type of nitrile oxide RCNO was greatly varied with R being isopentyl, tolyl, 2-pyridyl, and pentafluorophenyl. A detailed NMR spectroscopic investigation showed the formation of the 3,5-disubstituted isoxazole to be clearly favored (≥96%) over that of the constitutional isomeric 3,4-disubstituted isoxazole, except for one example.