Metallic solder based PCMs possess higher thermal conductivities, larger storage masses and exhibit lower subcooling effects compared to their organic or inorganic counterparts. It is thus justified to investigate their potential usage for medium temperature applications. These solders are relatively expensive and can be combined with cheaper PCMs in cascaded storage systems which are more thermodynamically efficient compared to single PCM systems as reported recently. The aim of the research is thus to compare two packed bed storage systems during discharging cycles using eutectic solder (Sn63/Pb37), that is widely available worldwide. The single PCM system (40 capsules) consists of encapsulated spheres of eutectic solder, whereas the second cascaded system consists of encapsulated spheres of eutectic solder and erythritol in an equal storage ratio in the tank. For the cascaded system, the eutectic solder capsules are placed at the top and erythritol at the bottom of the storage tank (20 capsules at the top and 20 at the bottom). The effect of the discharging flow-rates of 4 mL/s, 6 mL/s and 8 mL/s is investigated in relation to the temperature profiles, energy rates and exergy rates. Increasing the flow-rate, increases heat transfer rate thus shortening the discharging time as well as increasing thermal profile reversals during discharging. The peak energy and exergy rates increase with the increase in the flow-rate for the two storage systems. The single PCM system shows slightly higher average energy and exergy rates compared to the cascaded system possibly due to its higher thermal conductivity. The cascaded PCM system shows higher average stratification numbers at all the flow rates considered. The non-cascaded system exhibited slightly higher exergy recovery efficiencies compared to the cascaded PCM system possibly due to its higher thermal conductivity at all flow-rates considered. The effect of the initial discharging temperature is also investigated with a discharging flow-rate of 6 mL/s after charging with set heater temperatures of 260 C, 280 C and 300 C, respectively. Comparable thermal profiles are seen for both systems for the three set temperatures; however, the single PCM system shows slightly higher storage temperatures. The single PCM shows slightly higher but comparable peak and average discharging energy rates compared to the cascaded system. The exergy rates for the two systems are also comparable.
Latent heat storage systems consisting of phase change materials (PCMs) offer the advantage of a large thermal energy storage density as compared to sensible heat storage systems. Most recent work has focussed on organic and inorganic PCMs which have problems of subcooling and phase segregation. Metallic PCMs are a recent innovation for medium to high temperature applications due to their high thermal conductivities, high volumetric storage capacities and their low degrees of sub-cooling during the release of latent heat. For medium temperature applications like cooking of food, very limited work has been done on metallic PCMs for energy storage. Solder based PCMs have rarely been investigated for medium temperature applications thus it is necessary to carry out an experimental study on the use of a solder as PCM candidate. No work has ever been reported using the eutectic solder (Sn63/Pb37) as a PCM. Its use is justified since it is low cost and locally manufactured solder worldwide. Another recent innovation is cascaded thermal energy storage (TES), whereby two PCMs with different melting temperatures are used in a single storage tank to improve the efficiency of energy storage. No work has also appeared in recent literature involving metallic solders in cascaded systems. In a bid to investigate the suitability of the eutectic solder as a PCM for medium temperature applications, two eutectic solder (Sn63/Pb37) based systems are experimentally evaluated during discharging cycles. The first system is a single PCM system composed of a packed bed of spherically encapsulated eutectic solder capsules. The other system is a two PCM cascaded system comprising of eutectic solder spherical capsules at the top and erythritol spherical capsules at the bottom in a storage ratio of 50 %: 50 %. Discharging experiments are carried with three different discharging flow-rates to investigate the effect of the flow-rate on the thermal performance. The three discharging flow-rates used are 4 ml/s, 6 ml/s and 8 ml/s. For both storage systems, an increase in the discharging flow-rate increases the peak discharging energy and exergy rates. For both storage systems, an increase in the discharging flow-rate increases the peak discharging energy and exergy rates. The single PCM system shows higher energy and exergy rates for most of the discharging duration compared to the cascaded system. An increase in the flow-rate increases the peak energy and exergy discharging rates for the single PCM and the cascaded PCM storage systems. The single PCM system out-performed the cascaded system during the discharging tests possibly due to the lower melting temperature and lower thermal conductivity of the bottom PCM (erythritol) in the cascaded system. However, for the higher flow-rates (6 ml/s, 8 ml/s), the cascaded system shows a slightly better or comparable performance at the start and at end of discharging.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.