No abstract

Slip on unfavourably oriented faults with respect to a remotely applied stress is well documented and implies that faults such as the San Andreas fault and low-angle normal faults are weak when compared to laboratory-measured frictional strength. If high pore pressure within fault zones is the cause of such weakness, then stress reorientation within or close to a fault is necessary to allow sufficient fault weakening without the occurrence of hydrofracture. From field observations of a major tectonic fault, and using laboratory experiments and numerical modelling, here we show that stress rotation occurs within the fractured damage zone surrounding faults. In particular, we find that stress rotation is considerable for unfavourably oriented 'weak' faults. In the 'weak' fault case, the damage-induced change in elastic properties provides the necessary stress rotation to allow high pore pressure faulting without inducing hydrofracture.

[1] Subduction zone earthquakes can propagate to the surface causing large seafloor displacements resulting in tsunamis. This requires the earthquake to rupture through clay-rich sediments of the accretionary wedge, which are largely aseismic. As found previously, the frictional properties of a range of wet clays at low slip velocity are velocity strengthening, thus inhibiting earthquake nucleation. However, at high slip velocity the same materials weaken almost immediately resulting in a negligible critical slip weakening distance and fracture energy. We interpret this behaviour as rapid thermal pressurization of the pore fluid within the clay gouge. The lack of fracture energy can explain how a large rupture, propagating from depth, might not be arrested by clay-rich, velocity-strengthening sediments, as is commonly seen. The results suggest that generally, earthquakes may be difficult to nucleate on mature faults dominated by clay, but the propagation of earthquakes through these zones is energetically very favourable. Citation: Faulkner, D. R., T. M.

[1] Knowledge of the spatial extent of damage surrounding fault zones is important for understanding crustal fluid flow and also for understanding the physical processes and mechanics by which fault zones develop with slip. There are few data available on the scaling of the fault damage zone with fault displacement, and of those that exist, deriving scaling relationships is hampered by comparing faults that run through different lithologies, have formed at different crustal depths or tectonic regimes (e.g., normal versus strike-slip movement). We describe new data on the microfracture damage zone width from small displacement fault zones within the Atacama fault zone in northern Chile that formed at ∼6 km depth within a dioritic protolith. The microfracture damage zone is shown by an alteration halo surrounding the faults in which the density of the microfractures is much greater than background levels in the undeformed protolith. The data show that damage zone width increases with fault displacement and there appears to be a zero intercept to this relationship, meaning that at zero displacement, there is no microfracture damage zone. This is supported by field observations at fault tips that show a tapering out of fault damage zones. These data, combined with data from the literature, indicate that this same relationship might hold for much larger displacement faults. There is also a distinct asymmetry to the fracture damage. Several processes for the development of the observed scaling are discussed. The widely accepted theory of a process zone predicts that fault damage zone width increases with fault length and thus should always be largest at a propagating fault tip where displacement is lowest. This prediction is opposite to that seen in the current data set, leading to suggestion that other processes, such as damage zone growth with increasing displacement due to geometric irregularities or coseismic damage formation might better explain the spatial extent of damage surrounding even low-displacement faults.Citation: Faulkner, D. R., T. M. Mitchell, E. Jensen, and J. Cembrano (2011), Scaling of fault damage zones with displacement and the implications for fault growth processes,

[1] Detailed experimental studies of the development of permeability of crustal rock during deformation are essential in helping to understand fault mechanics and constrain larger-scale models that predict bulk fluid flow within the crust. Permeability is particularly enhanced in the damage zone of faults, where microfracture damage accumulates under stress less than that required for macroscopic failure. Experiments performed in the prefailure region can provide data directly applicable to these zones of microfracture damage surrounding faults. The strength, permeability, and pore fluid volume evolution of initially intact crystalline rocks (Cerro Cristales granodiorite and Westerly granite) under increasing differential load leading to macroscopic failure has been determined at water pore pressures of 50 MPa and varying effective pressures from 10 to 50 MPa. Permeability is seen to increase by up to, and over, 2 orders of magnitude prior to macroscopic failure, with the greatest increase seen at lowest effective pressures. Postfailure permeability is shown to be over 3 orders of magnitude higher than initial intact permeabilities and approaches the lower limit of predicted in situ bulk crustal permeabilities. Increasing amplitude cyclic loading tests show permeability-stress hysteresis, with high permeabilities maintained as differential stress is reduced and the greatest permeability increases are seen between 90 and 99% of the failure stress. Prefailure permeabilities are nearly 7 to 9 orders of magnitude lower than that predicted by some high-pressure diffusive models suggesting that if these models are correct, microfracture matrix flow cannot dominate, and that bulk fluid flow must be dominated by larger-scale structures such as macrofractures. We present a model, based on our data, in which the permeability of a highly stressed fault tip process zone in low-permeability crystalline rocks increases by more than 2 orders of magnitude. Stress reduction related to the onward migration of the fault tip close damage zone cracks, while some permeability is maintained due to hysteresis from permanent microfracture damage.Citation: Mitchell, T. M., and D. R. Faulkner (2008), Experimental measurements of permeability evolution during triaxial compression of initially intact crystalline rocks and implications for fluid flow in fault zones,

No abstract

Previous studies show that pulverized rocks observed along large faults can be created by single high‐strain rate loadings in the laboratory, provided that the strain rate is higher than a certain pulverization threshold. Such loadings are analogous to large seismic events. In reality, pulverized rocks have been subject to numerous seismic events rather than one single event. Therefore, the effect of successive “milder” high‐strain rate loadings on the pulverization threshold is investigated by applying loading conditions below the initial pulverization threshold. Single and successive loading experiments were performed on quartz‐monzonite using a Split Hopkinson Pressure Bar apparatus. Damage‐dependent petrophysical properties and elastic moduli were monitored by applying incremental strains. Furthermore, it is shown that the pulverization threshold can be reduced by successive “milder” dynamic loadings from strain rates of ~180 s−1 to ~90 s−1. To do so, it is imperative that the rock experiences dynamic fracturing during the successive loadings prior to pulverization. Combined with loading conditions during an earthquake rupture event, the following generalized fault damage zone structure perpendicular to the fault will develop: furthest from the fault plane, there is a stationary outer boundary that bounds a zone of dynamically fractured rocks. Closer to the fault, a pulverization boundary delimits a band of pulverized rock. Consecutive seismic events will cause progressive broadening of the band of pulverized rocks, eventually creating a wider damage zone observed in mature faults.

No abstract