The overall cooling effectiveness for a turbine airfoil was quantified based on the external surface temperature relative to the mainstream temperature and the inlet coolant temperature. This can be determined experimentally when the model is constructed so that the Biot number is similar to that of engine components. In this study, the overall cooling effectiveness was experimentally measured on a model turbine vane constructed of a material deigned to match Bi for engine conditions. The model incorporated an internal impingement cooling configuration. Overall cooling effectiveness and adiabatic film effectiveness were measured downstream of a single row of round holes positioned on the suction side of the vane. Experiments were conducted to evaluate the cooling effects of internal cooling alone, and then the combined effects of film cooling and internal cooling for a range of coolant flow rates. While the adiabatic film effectiveness decreased when using high momentum flux ratios for the film cooling, due to coolant jet separation, the overall cooling effectiveness increased at higher momentum flux ratios. This increase was due to increased internal cooling effects. Overall cooling effectiveness measurements were also compared to analytical predictions based on a 1D thermal analysis using measured adiabatic film effectiveness and overall cooling effectiveness without film cooling.
There have been a number of previous studies of the adiabatic film effectiveness for the showerhead region of a turbine vane, but no previous studies of the overall cooling effectiveness. The overall cooling effectiveness is a measure of the external surface temperature relative to the mainstream temperature and the inlet coolant temperature, and consequently is a direct measure of how effectively the surface is cooled. This can be determined experimentally when the model is constructed so that the Biot number is similar to that of engine components, and the internal cooling is designed so that the ratio of the external to internal heat transfer coefficient is matched to that of the engine. In this study, the overall effectiveness was experimentally measured on a model turbine vane constructed of a material to match Bi for engine conditions. The model incorporated an internal impingement cooling configuration. The cooling design consisted of a showerhead composed of five rows of holes with one additional row on both pressure and suction sides of the vane. An identical model was also constructed out of low conductivity foam to measure adiabatic film effectiveness. Of particular interest in this study was to use the overall cooling effectiveness measurements to identify local hot spots which might lead to failure of the vane. Furthermore, the experimental measurements provided an important database for evaluation of CFD simulations of the conjugate heat transfer effects that occur in the showerhead region. Continuous improvement in both measures of performance was demonstrated with increasing momentum flux ratio.
The overall cooling effectiveness for a turbine airfoil was quantified based on the external surface temperature relative to the mainstream temperature and the inlet coolant temperature. This can be determined experimentally when the model is constructed so that the Biot number is similar to that of engine components. In this study, the overall cooling effectiveness was experimentally measured on a model turbine vane constructed of a material deigned to match Bi for engine conditions. The model incorporated an internal impingement cooling configuration. Overall cooling effectiveness and adiabatic film effectiveness were measured downstream of a single row of round holes positioned on the suction side of the vane. Experiments were conducted to evaluate the cooling effects of internal cooling alone, and then the combined effects of film cooling and internal cooling for a range of coolant flow rates. While the adiabatic film effectiveness decreased when using high momentum flux ratios for the film cooling, due to coolant jet separation, the overall cooling effectiveness increased at higher momentum flux ratios. This increase was due to increased internal cooling effects. Overall cooling effectiveness measurements were also compared to analytical predictions based on a 1D thermal analysis using measured adiabatic film effectiveness and overall cooling effectiveness without film cooling.
There have been a number of previous studies of the adiabatic film effectiveness for the showerhead region of a turbine vane, but no previous studies of the overall cooling effectiveness. The overall cooling effectiveness is a measure of the external surface temperature relative to the mainstream temperature and the inlet coolant temperature, and consequently is a direct measure of how effectively the surface is cooled. This can be determined experimentally when the model is constructed so that the Biot number is similar to that of engine components, and the internal cooling is designed so that the ratio of the external to internal heat transfer coefficient is matched to that of the engine. In this study, the overall effectiveness was experimentally measured on a model turbine vane constructed of a material to match Bi for engine conditions. The model incorporated an internal impingement cooling configuration. The cooling design consisted of a showerhead composed of five rows of holes with one additional row on both pressure and suction sides of the vane. An identical model was also constructed out of low conductivity foam to measure adiabatic film effectiveness. Of particular interest in this study was to use the overall cooling effectiveness measurements to identify local hot spots which might lead to failure of the vane. Furthermore, the experimental measurements provided an important database for evaluation of computational fluid dynamics simulations of the conjugate heat transfer effects that occur in the showerhead region. Continuous improvement in both measures of performance was demonstrated with increasing momentum flux ratio.
Computational simulations using a steady RANS approach with the k-ω SST turbulence model were performed to complement experimental measurements of overall cooling effectiveness and adiabatic film effectiveness for a film cooled turbine vane airfoil. The vane included a single row of holes located on the suction side of the airfoil. The simulated geometry also included the internal impingement cooling configuration. Internal and external boundary conditions were matched to experiments using the same vane model. To correctly simulate conjugate heat transfer effects, the experimental vane model was constructed to match the Biot number for engine conditions. Computational predictions of the overall cooling effectiveness and adiabatic film effectiveness were compared to experimental measurements. The CFD predictions showed that the k-ω SST RANS model over-predicted local adiabatic film effectiveness for an attached jet, while performance was under-predicted for a detached jet. The corresponding predictions of overall cooling effectiveness were also over and under-predicted. Further, it was shown that the adiabatic wall temperature was not the correct driving temperature for heat transfer, especially in the case of a detached jet.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.