Background: Clinical studies reporting the outcome of zirconia-based restorations indicate that the strength of the zirconia frameworks is sufficient to withstand masticatory forces. However, a significant incidence of cohesive fracture of the veneering porcelain has been reported. The aim of this study was to investigate spontaneous crack development (chipping, rupture) in a range of porcelains veneered to a zirconia core as a result of thermal stresses induced by changes in thickness and cooling rate. The hypothesis tested was that crack incidence would increase with increased veneer thickness and faster cooling rates. Methods: Zirconia spheres (diameter 7.8 mm) were veneered with 1.5 gm (thickness ratio 1:2) and 2.5 gm (thickness ratio 1:1) of five nominally compatible commercially available porcelains. The manufacturers' firing cycles and a rapid cooling firing cycle were followed. Results: Multiple regression analysis showed positive associations between the occurrence of cracks and the three covariates (materials, thickness and cooling rate). The incidence of cracks and rupture of the veneering porcelain increased with a faster cooling rate and increased thickness of the specimens in three porcelain-zirconia combinations. Conclusions: Crack incidence increased with increased porcelain veneer thickness and faster cooling rates in nominally compatible porcelain ⁄ zirconia systems in the geometrically configured specimens tested.

This assignment applies to all translations of the Work as well as to preliminary display/posting of the abstract of the accepted article in electronic form before publication. If any changes in authorship (order, deletions, or additions) occur after the manuscript is submitted, agreement by all authors for such changes must be on file with the Publisher. An author's name may be removed only at his/her written request. (Note: Material prepared by employees of the US government in the course of their official duties cannot be copyrighted.

To assess and compare the outcomes and economic complication burden of three-unit toothsupported fixed dental prostheses (TFDPs) and implant-supported single crowns (ISCs) provided to a sequential cohort in a specialist prosthodontic practice over a 15-year period. Materials and Methods: Sequential patients requiring replacement of a single missing tooth between 1996 and 2010 with a metal-ceramic three-unit TFDP (n = 145 patients, n = 174 prostheses) or ISC (n = 174 patients, n = 220 prostheses) were included. Prostheses subjectively judged at insertion to have an unfavorable 10-year prognosis (17 TFDPs, 0 ISCs) were removed from statistical analyses. The estimated cumulative survival (ECS) was calculated with the life table actuarial method and standard errors calculated with the Greenwood formula. Differences in outcomes between all prostheses and those replacing only anterior or only posterior teeth were assessed with the log rank test. Complication incidence, severity, and economic burden, measured in time/cost accounting units (TAUs), were tallied and compared descriptively. Results: The 15-year ECS did not differ for 112 TFDPs (92.75% ± 3.28%) and 81 ISCs (95.95% ± 2.92%) replacing posterior teeth. However, the 15-year ECS was significantly greater for 139 ISCs (93.33% ± 6.44%) than for 45 TFDPs (82.82% ± 6.50%) replacing anterior teeth. The economic burden of nonterminal complications for both prostheses was low (mean = 0.3 and 0.2 TAUs per prosthesis for TFDPs and ISCs, respectively). This equated to 3 TAUs/100 years in clinical service and 4 TAUs/100 years in clinical service for the TFDPs and ISCs, respectively. Conclusion: The survival of three-unit TFDPs and ISCs over 15 years was not statistically different when replacing posterior teeth, but ISCs survived significantly better when replacing anterior teeth. The complication rates of the TFDPs and ISCs were similar, but the economic burden for the TFDPs was greater.

Patients with SICs that were in situ up to 14 years who responded to the validated PSQ were highly satisfied with the appearance and cleansibility, noted improvements in peri-implant tissue contours, and found the treatment to be valuable and worthwhile. They reported that upfront costs were high, but this concern decreased when the SICs had been in the mouth for a period of time.

Cracking or rupturing, due to thermal stress, of porcelain bonded to a palladium-silver alloy indicated that porcelain-metal thermal compatibility was dependent on: the difference in thermal expansion coefficients of the porcelain and metal; the geometry and dimensions of the samples; and the porcelain-metal thickness ratio. A spherical configuration was more sensitive to thermal expansion coefficient differences than was a disc configuration. A higher incidence of cracking resulted from an increase in both specimen size and porcelain-metal thickness ratio.

Agreement within and between examiners when assessing MBLs was poor. Disagreement occurred around 25% of the time, potentially affecting consistent disease assessments. No participant or implant characteristic clearly affected agreement. Brighter radiographs improved intra-examiner agreement. Overall, perceived MBL changes below 1 mm are likely due to human, not biological variation.

No abstract

This assignment applies to all translations of the Work as well as to preliminary display/posting of the abstract of the accepted article in electronic form before publication. If any changes in authorship (order, deletions, or additions) occur after the manuscript is submitted, agreement by all authors for such changes must be on file with the Publisher. An author's name may be removed only at his/her written request. (Note: Material prepared by employees of the US government in the course of their official duties cannot be copyrighted.