We present a spectroelectrochemical fiber-optic sensor with an optically transparent electrode. The sensor was fabricated by coating indium tin oxide (ITO) onto the surface of fiber-optic core chips using a polygonal barrel-sputtering method. The ITO-coated fiber-optic probe can be simply and cheaply mass-produced and used as a disposable probe. The sensing is based on changes in an attenuated total reflection signal accompanying the electrochemical oxidation-reduction of an analyte at the electrode. The properties of an ITO-coated fiber-optic probe as an optically transparent electrode were investigated for varying thicknesses of ITO. The sensor responses were successfully enhanced with an additional level of selectivity via an electrostatically adsorbed, self-assembled monolayer, which comprised a polyanion and polycation.

We present a novel fiber optic sensor for real-time sensing of silica scale formation in geothermal water. The sensor is fabricated by removing the cladding of a multimode fiber to expose the core to detect the scale-formation-induced refractive index change. A simple experimental setup was constructed to measure the transmittance response using white light as a source and a spectroscopy detector. A field test was performed on geothermal water containing 980 mg/L dissolved silica at 93 °C in Sumikawa Geothermal Power Plant, Japan. The transmittance response of the fiber sensor decreased due to the formation of silica scale on the fiber core from geothermal water. An application of this sensor in the evaluation of scale inhibitors was demonstrated. In geothermal water containing a pH modifier, the change of transmittance response decreased with pH decrease. The effectiveness of a polyelectrolyte inhibitor in prevention of silica scale formation was easily detectable using the fiber sensor in geothermal water.

We present an electrochemical long period fiber grating (LPFG) sensor for electroactive species with an optically transparent electrode. The sensor was fabricated by coating indium tin oxide onto the surface of LPFG using a polygonal barrel-sputtering method. LPFG was produced by an electric arc-induced technique. The sensing is based on change in the detection of electron density on the electrode surface during potential application and its reduction by electrochemical redox of analytes. Four typical electroactive species of methylene blue, hexaammineruthenium­(III), ferrocyanide, and ferrocenedimethanol were used to investigate the sensor performance. The concentrations of analytes were determined by the modulation of the potential as the change in transmittance around the resonance band of LPFG. The sensitivity of the sensor, particularly to methylene blue, was high, and the sensor responded to a wide concentration range of 0.001 mM to 1 mM.

Treatment with an electromagnetic field, one of the potential techniques to inhibit scale deposition from water, has the advantage of not requiring the addition of any chemicals. Field tests using a fibre optic sensor were conducted to evaluate the effect that the treatment of hot spring water in Matsushiro, Japan with an electromagnetic field had on calcium carbonate scale formation. The optical response to scale deposition recorded by the fibre optic sensor decreased as a consequence of the application of an electromagnetic field, and the effectiveness of scale formation inhibition depended on the frequency of the electromagnetic field. This evidence was compared with results from changes in scale mass measured using the quartz crystal microbalance (QCM) method. Mass increases of the scale formed on the quartz crystal surface in hot spring water were inhibited by electromagnetic field treatment. These results were verified performing a column flow test, whereby the flow rate of hot spring water through a column was measured.

No abstract

We present an electrochemical‐lossy mode resonance (LMR) sensing method that detects refractive indices and electroactive species. The LMR peaks of indium‐tin‐oxide in the transmittance‐wavelength spectra were significantly shifted as the applied potential between 1.0 and −0.5 V at 209 nm/V. The modulation was exploited for sensing the refractive index and electroactive species (ferrocyanide and methylene blue) in two ways: peak‐wavelength tracking and potential scanning. The potential‐scanning technique produced clear potential LMR peaks in the transmittance‐potential spectra for the first time, which were corresponded to the external refractive index. Meanwhile, the limits of detection of ferrocyanide and methylene blue were 7.5 and 25.3 μM, respectively, in peak‐wavelength tracking and 18.2 and 20.8 μM, respectively, in the potential scanning technique.

No abstract

No abstract