Ellis-van Creveld syndrome (EVC) is a very rare genetic disorder that affects various tissues of ectodermal and mesodermal origin; patients with EVC present with typical oral deficiencies. The affected individuals are quite young at the time of oral evaluation. It is, therefore, important that these individuals are diagnosed and receive dental treatment at an early age for their physiologic and psychosocial well-being. Albeit there are numerous articles penned on the EVC, the treatise from an oral perspective is inadequate, covering only oral exhibitions and the preventive treatments. This article reviews the literature and serves as the first disquisition for oral rehabilitation of an EVC patient utilizing surgical, orthodontic, restorative, and prosthodontic management.

No abstract

Objective: The most important desideratum of a provisional crown is an adequate marginal fit that is essential for maintaining optimal periodontal health, reducing the sensitivity of freshly prepared dentin and protection of the pulp. The purpose of this in vitro study was to compare the vertical marginal accuracy of provisional crown materials using three different material systems (chemically activated PMMA powder-liquid system, light activated UDMA single paste system, and chemically activated Bis-GMA two paste auto mix system) and two different techniques (direct and indirect). Methods: Two customized stainless steel dies, simulating prepared and unprepared tooth were used to fabricate 40 provisional crowns. Additional silicone elastomeric impression and a vacuum-formed polypropylene sheet were used as a matrix. Ten crowns, each of the three material systems used in the study (n = 10 × 3) were fabricated using the direct technique and ten crowns from chemically activated PMMA powder-liquid system (n = 10 × 1) using an indirect technique. Scanning electron microscope (SEM) was used to measure vertical marginal discrepancies at x100 magnification. The results were analyzed using descriptive statistics and comparisons between various groups were made using one way analysis of variance (ANOVA) after checking the normality of data using Shapiro Wilk’s Test. Post Hoc Tukey HSD Test was used to determine the statistical difference between the means of independent group pairs. Results: The mean marginal discrepancies of Bis-GMA composite resin, UDMA composite resin, and PMMA acrylic resin using direct technique were 67.15 µm, 71.01 µm, and 84.56 µm respectively. PMMA acrylic resin showed a mean marginal discrepancy of 103.03 µm using the indirect technique. Conclusion: This study has shown that provisional crowns fabricated with Bis-GMA composite resin material (two paste auto mix system) registered the best marginal accuracy. Provisional crowns fabricated with indirect technique recorded less marginal opening than with direct technique. How to cite this:Naqash TA, Alfarsi M, Hussain MW. Marginal accuracy of provisional crowns using three material systems and two techniques: A scanning electron microscope study. Pak J Med Sci. 2019;35(1):---------. doi: https://doi.org/10.12669/pjms.35.1.5 This is an Open Access article distributed under the terms of the Creative Commons Attribution License (http://creativecommons.org/licenses/by/3.0), which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Splinting of the mobile teeth is a critical part of periodontal management to improve the prognosis and longevity of stable results of periodontally compromised teeth with increased mobility. Different types of splints are used in the dental field based on their mechanical and physical properties.The objective of the current in vitro study was to evaluate the flexure strength and flexural modulus of different types of splinting materials, such as: composite block, ligature wire, Ribbond®, InFibra®, and F-splint-Aid® bonded utilizing Flowable composites resin material. Seventy-five bar specimens were prepared with the dimensions of 25 × 4 × 2 mm, utilizing split metallic mold. Specimens were divided equally (n = 15) into five groups (one control group, four test groups). Different layers of splinting material were placed in between the layers of composite before curing. All the specimens were subjected to a three-point bending test by using a universal testing machine to calculate the flexural strength and flexural modulus. The entire data was subjected to statistical tests to evaluate the significance. Specimens from composite block groups showed the least mean value for flexural strength (89.15 ± 9.70 MPa) and flexural modulus (4.310 ± 0.912 GPa). Whereas, the highest mean value for flexural strength (168.04 ± 45.95 MPa) and flexural modulus (5.861 ± 0.501 GPa) were recorded by Ribbond® specimens. Inter group comparison of flexural strength showed statistically significant differences (P-value < 0.05), whereas comparison of flexural modulus showed non-significant difference among the groups (P-value > 0.05). Within the limitation of the present study, it was concluded that the Ribbond® exhibits maximum flexural strength and flexural modulus, whereas the composite blocks recorded the least values. Still, the decision making depends on the clinical scenario and the unique characteristic of each splint material.

The sole objective of casting procedure is to provide a metallic duplication of missing tooth structure, with as great accuracy as possible. The ability to produce well fitting castings require strict adherence to certain fundamentals. A study was undertaken to comparatively evaluate the effect on casting accuracy by subjecting the invested wax patterns to burnout after different time intervals. The effect on casting accuracy using metal ring into a pre heated burnout furnace and using split ring was also carried. The readings obtained were tabulated and subjected to statistical analysis.