In this work, we report an ultrasensitive hydrogen (H2) sensor based on tungsten trioxide (WO3) nanorods decorated with platinum (Pt) nanoparticles. WO3 nanorods were fabricated by dc magnetron sputtering with a glancing angle deposition (GLAD) technique, and decorations of Pt nanoparticles were performed by normal dc sputtering on WO3 nanorods with varying deposition time from 2.5 to 15 s. Crystal structures, morphologies, and chemical information on Pt-decorated WO3 nanorods were characterized by grazing-incident X-ray diffraction, field-emission scanning electron microscopy, energy-dispersive X-ray spectroscopy, and photoelectron spectroscopy, respectively. The effect of the Pt nanoparticles on the H2-sensing performance of WO3 nanorods was investigated over a low concentration range of 150-3000 ppm of H2 at 150-350 °C working temperatures. The results showed that the H2 response greatly increased with increasing Pt-deposition time up to 10 s but then substantially deteriorated as the deposition time increased further. The optimally decorated Pt-WO3 nanorod sensor exhibited an ultrahigh H2 response from 1530 and 214,000 to 150 and 3000 ppm of H2, respectively, at 200 °C. The outstanding gas-sensing properties may be attributed to the excellent dispersion of fine Pt nanoparticles on WO3 nanorods having a very large effective surface area, leading to highly effective spillover of molecular hydrogen through Pt nanoparticles onto the WO3 nanorod surface.

No abstract

Tungsten trioxide (WO3) thin films were prepared by a DC reactive magnetron sputtering technique. The thin film fabrication process used tungsten (99.995%) as the sputtering target, the mixture of argon and oxygen as sputtering and reactive gases, and silicon (100) and glass slides as the substrates. The effects of annealing temperature in the range of 200-400°C on physical and optical properties of the WO3 thin films were investigated. The nanostructures and morphologies of these films were characterized by grazing-incident X-ray diffraction (GIXRD) and field-emission scanning electron microscopy (FE-SEM). The optical properties were analyzed by variable-angle spectroscopic ellipsometry (VASE) and spectrophotometer. From the XRD results, the as-deposited and annealed WO3 thin films up to 300°C were all amorphous. Only the WO3 thin film annealed at 400°C exhibited a polycrystalline monoclinic phase. The FE-SEM cross-sections and surface topologies demonstrated nearly identical thin-film thickness and physical grain sizes. The SE analyses showed that the thin films were all homogeneous dense layers with additional surface roughness. With the annealing treatment, the thin film thickness was slightly decreased. The SE physical model was best optimized with the Cauchy optical model. The results showed that the refractive index at 550 nm was increased from 2.17 to 2.23 with the increased annealing temperature. The results from the spectrophotometer confirmed that the optical spectra for the WO3 thin films were decreased. This study demonstrated that, the thin film annealed at 400°C exhibited the slightly lower transparency, which corresponded to the results from the GIXRD and SE analyses.

Tungsten oxide (WO3) nanorods were prepared by a DC reactive magnetron sputtering with a glancing-angle deposition (GLAD) technique, which promoted high surface area, for electrochromic applications. During the deposition, a high-quality tungsten target was sputtered under oxygen ambience on to Si (100) and glass/ITO substrates. The variation of the deposition time, which affected the length, size and patterns of the nanorods, was investigated based on their electrochromic properties. For physical studies, the prepared nanorods were examined by X-ray diffraction and field-emission scanning electron microscopy, which demonstrated moderately ordered nanorods with amorphous phase. The results showed that the length and size of nanorod were increased, in nearly linear order, with increasing the deposition time. For optical characteristics of the prepared films, the UV-Vis spectrophotometry was use to determined their transmission spectra and optical contrasts from the colored and bleached state. The electrochromic properties were also determined from cyclic voltammetry. The results indicated that, because of the optimal relations between the nanostructural length and size, the WO3 nanorods prepared at 75 minutes (approximately 422 nm) yielded the highest optical contrast and electrochromic functions.

Tantalum oxide (Ta2O5) thin films were prepared, at different deposition time, by a DC reactive magnetron sputtering. During the deposition, a high-quality tantalum target was sputtered under argon and oxygen ambience on to silicon (100) and glass substrates. The prepared thin films were systematically characterized for both physical and optical properties based on spectroscopic ellipsometry (SE), and consequently confirmed by several methods. With the SE physical models, we could determine the thin film thickness as well as their inhomogeneity. The films thickness results were directly confirmed by field-emission scanning electron microscopy (FE-SEM) used to observe cross-sections, and surface profiler used to measure the physical thickness of the films. With the SE optical models, we applied both the Cauchy and Tauc-Lorentz dispersions in order to obtain the optical constants, to be directly compared with those from the Swanepoel method (SM). Our result showed that from the SE analyses, the SE physical model was obtained as the multi-layer configurations. The obtained Ta2O5 thin film thickness was closely related with the measured result from the FE-SEM cross-sectional micrographs and the surface profiler. For the optical characteristic, the double layer physical model was best optimized with the Tauc Lorentz dispersion model for the most accurate results. In comparison, the SM technique also demonstrated a capability to determine both the film thickness and its refractive index only from some samples. Therefore, this study proved that the SE technique successfully and accurately determine both the physical and optical properties of the Ta2O5 thin films.