No abstract

Spallation induced by a laser driven shock has been studied for two decades on time scales of nanosecond order. The evolution of laser technologies now opens access to sources whose pulse duration is under the picosecond, corresponding to characteristic times of numerous microscopic phenomena. In this ultra-short irradiation regime, spallation experiments have been performed with time-resolved measurements of the free surface. These measurements, complemented with post-test observations, have been compared with numerical simulations to check the consistency of modelling of the laser–matter interaction, shock propagation and to the study of dynamic damage at this ultra-short time scale, inducing strong tensile stress states at very high strain rates.

International audienc

No abstract

International audienceIn the natural case of an hypervelocity impact on a planetary or asteroidal surface, two competing phenomena occur: partial or complete shock demagnetization of pre-existing remanence and acquisition of shock remanent magnetization (SRM). In this paper, to better understand the effects of shock on the magnetic history of rocks, we simulate this natural case through laser shock experiments in controlled magnetic field. As previously shown, SRM is strictly proportional to the ambient field at the time of impact and parallel to the ambient field. Moreover, there is no directional or intensity heterogeneity of the SRM down to the scale of ∼0.2mm. We also show that the intensity of SRM is independent of the initial remanence state of the rock. Shock demagnetization and magnetization appear to be distinct phenomena that do not necessarily affect identical populations of grains. As such, shock demagnetization is not a limiting case of shock magnetization in zero field

Strength and elastic deformation of natural and synthetic diamond crystals shock compressed along [100] J.A series of magnesium single crystals, from 0.2 to 3 mm thick, were shock loaded in directions parallel and perpendicular to the c-axis of the hexagonal closed packed (hcp) structure and at 45 to the c-axis. Shock compression along the c-axis is associated with the largest Hugoniot elastic limit (HEL) for this material. Microscopic observation of recovered c-cut samples demonstrated intense twinning with a greater density of twins near the impact surface. The low-energy basal slip was activated by shock loading along the inclined direction and has the smallest HEL. In all cases, we observe the decay of the elastic precursor wave and growth of the HEL with increasing temperature. For the inclined shock compression after the HEL, two plastic waves were found where the stress level of the first plastic wave depends on the peak shock stress. Finally, the largest spall strength was along the transversal direction and the smallest in the off-axis direction. The fracture surface of the sample of transversal orientation contains numerous groves oriented along the base planes of the crystals. V C 2014 AIP Publishing LLC. [http://dx.

When a shock wave propagating in a solid sample reflects from a free surface, geometrical effects predominantly governed by the roughness and defects of that surface may lead to the ejection of tiny jets that may breakup into high velocity, approximately micrometer-size fragments. This process referred to as microjetting is a major safety issue for engineering applications such as pyrotechnics or armour design. Thus, it has been widely studied both experimentally, under explosive and impact loading, and theoretically. In this paper, microjetting is investigated in the specific loading conditions associated to laser shocks: very short duration of pressure application, very high strain rates, small spatial scales. Material ejection from triangular grooves in the free surface of various metallic samples is studied by combining transverse optical shadowgraphy and time-resolved velocity measurements. The influences of the main parameters (groove angle, shock pressure, nature of the metal) on jet formation and ejection velocity are quantified, and the results are compared to theoretical estimates.

Spallation of materials induced by laser driven shock waves is generally produced under uniaxial (one-dimensional (1D)) deformation by irradiating a spot of diameter much greater than the sample thickness. Here, two-dimensional (2D) effects are introduced in shock wave propagation by drastically reducing the loaded spot. Experiments performed on aluminium samples detect the effect of lateral wave propagation, both on recovered samples and on time-resolved VISAR measurements. Damage zones are localized completely differently from that under uniaxial condition, according to the presence of 2D effects, and the signature of these 2D effects can be read on VISAR signals. Numerical simulations provide a full understanding of wave propagation and resulting damage in 1D or 2D configuration. Comparisons with experimental VISAR signals show the possibility of validating more accurately the dynamic damage criteria, including the 2D effects.