Mechanical loading in the proximal radius was increased by ulnar osteotomy (Group O), altered by Steinmann pinning (Group P) or unaltered in sham operated controls (Group C) in skeletally mature female sheep, aged 2-4 years.A series of intravenous fluorochromes were given to label bone formation and fuchsin-stained microdamage assessed at intervals of up to 24 weeks. Microcracks were present in all groups and were found in the original cortex near the periosteal surface. No microcracks were found in the new, fibrolamellar bone laid down at periosteal or endosteal surfaces. Mean microcrack length (49 µ m, SD 10 µ m) did not differ between groups or over time. Microcrack numerical and surface densities and resorption cavity density peaked in all groups at 6 weeks, consistent with a regional acceleratory phenomenon (RAP), but the peaks were significantly greater in Group O. The density of refilling or secondary osteons peaked at 10 weeks and the mean time required for the formation of an osteon was 7.51 ± 0.59 weeks. Fatigue-induced microdamage is normally present in bone and is increased due to repetitive loading of the mechanically overloaded radius. The location and timing of microcracks, resorption cavities and secondary osteons are consistent with the activation-resorption-formation remodelling cycle and suggest that microdamage is a stimulus for bone remodelling.

Fatigue-induced microdamage in bone contributes to stress and fragility fractures and acts as a stimulus for bone remodelling. Detecting such microdamage is difficult as pre-existing microdamage sustained in vivo must be differentiated from artefactual damage incurred during specimen preparation. This was addressed by bulk staining specimens in alcohol-soluble basic fuchsin dye, but cutting and grinding them in an aqueous medium. Nonetheless, some artefactual cracks are partially stained and careful observation under transmitted light, or epifluorescence microscopy, is required. Fuchsin lodges in cracks, but is not site-specific. Cracks are discontinuities in the calciumrich bone matrix and chelating agents, which bind calcium, can selectively label them. Oxytetracycline, alizarin complexone, calcein, calcein blue and xylenol orange all selectively bind microcracks and, as they fluoresce at different wavelengths and colours, can be used in sequence to label microcrack growth. New agents that only fluoresce when involved in a chelate are currently being developed -fluorescent photoinduced electron transfer (PET) sensors. Such agents enable microdamage to be quantified and crack growth to be measured and are useful histological tools in providing data for modelling the material behaviour of bone. However, a non-invasive method is needed to measure microdamage in patients. Micro-CT is being studied and initial work with iodine dyes linked to a chelating group has shown some promise. In the long term, it is hoped that repeated measurements can be made at critical sites and microdamage accumulation monitored. Quantification of microdamage, together with bone mass measurements, will help in predicting and preventing bone fracture failure in patients with osteoporosis.

The effectiveness of a cardiovascular stent depends on many factors, such as its ability to sustain the compression applied by the vessel wall, minimal longitudinal contraction when it is expanded, and its ability to flex when navigating tortuous blood vessels. The long-term reaction of the tissue to the stent is also device dependant; in particular some designs provoke in-stent restenosis (i.e., regrowth of the occlusion around the stent). The mechanism of restenosis is thought to involve injury or damage to the vessel wall due to the high stresses generated around the stent when it expands. Because of this, the deflection of the tissue between the struts of the stent (called prolapse or "draping") has been used as a measure of the potential of a stent to cause restenosis. In this paper, uniaxial and biaxial experiments on human femoral artery and porcine aortic vascular tissue are used to develop a hyperelastic constitive model of vascular tissue suitable for implementation in finite-element analysis. To analyze prolapse, four stent designs (BeStent 2, Medtronic AVE; NIROYAL, Boston Scientific; VELOCITY, Cordis; TETRA, Guidant) were expanded in vitro to determine their repeating-unit dimensions. This geometric data was used to generate a finite element model of the vascular tissue supported within a repeating-unit of the stent. Under a pressure of 450 mm Hg (representing the radial compression of the vessel wall), maximum radial deflection of 0.253 mm, 0.279 mm, 0.348 mm and 0.48 mm were calculated for each of the four stents. Stresses in the vascular wall were highest for the VELOCITY stent. The method is proposed as a way to compare stents relative to their potential for restenosis and as a basis for a biomechanical design of a stent repeating-unit that would minimize restenosis.

Microdamage in bone contributes to the loss of bone quality in osteoporosis and is thought to play a major role in both fragility and stress fractures (Schaffler et al. 1995). In this study, in vivo microcracks in human ribs were bulk-stained in basic fuchsin and viewed in longitudinal section and in 3 dimensions using 2 different computer-based methods of reconstruction : (1) serial sectioning of methylmethacrylate embedded sections using a sledge macrotome and identification of microcracks using UV epifluorescence followed by computerised reconstruction of microcracks using software and (2) laser scanning confocal microscopy of thick sections followed by reconstruction of microcracks into a 3-D image. The size and shape of microcracks were found to be similar using both techniques. Both techniques of reconstruction showed microcracks to be approximately elliptical in shape. From the serial sectioning reconstructions (n l 9), microcracks were found to have a mean length of 404p145 µm (meanp..) (in the longitudinal direction) and mean width of 97p38 µm (in the transverse direction). Using epifluorescence microscopy, 92 microcracks were identified ; mean microcrack length was 349p100 µm in the longitudinal direction. This was consistent with other results (Burr & Martin, 1993) and with the theoretical prediction of an elliptical crack shape with aspect ratio (longitudinal : transverse) of 5 : 1 deduced from analysis of random 2-D sections (Taylor & Lee, 1998). The results obtained provide new data on the nature of microcracks in bone and the method has the potential to become a useful tool in the calculation of stress intensity values which indicate the probability of an individual microcrack propagating to cause a stress or fragility fracture.