Among agricultural soil amendment that can enhance crop productivity and soil sustainability is biochar. Hence, two-year field experiments were conducted on a sandy loam Alfisol at Owo, southwest Nigeria, to evaluate the effects of biochar produced from hardwood on soil physical and chemical characteristics, erosion potential, and cocoyam (Xanthosoma sagittifolium (L.) Schott) yield. The study was a 2 × 4 factorial experiment with two years (2017 and 2018) and four biochar levels (0 (control), 10, 20, and 30 t ha−1). The treatments were laid out in a randomized complete block design with three replications. Results indicated that biochar application significantly in both years improved yield of cocoyam and soil physical (bulk density, porosity, moisture content, mean weight diameter (MWD) of soil aggregates, dispersion ratio, and infiltration rate) and chemical (soil organic matter, pH, N, P, K, Ca, Mg, and CEC) properties and erosion resistance. Soil characteristics and cocoyam yield improved with level of biochar from 0–30 t ha−1. When 2018 is compared with 2017 in term of soil loss, in the amended plots, 2018 reduced soil loss by 7.4, 20, and 73.5%, respectively, for 10, 20, and 30 t ha−1biochar, whereas there was an increase of 2.7% soil loss in the control plot in 2018 compared with 2017. Therefore, application rate of 30 t ha−1 biochar is considered as suitable for severely degraded soil because this application rate efficiently improves cocoyam yield and soil properties and reduces soil loss.

Mechanical properties of ukam, banana, sisal, coconut, hemp and E-glass fibre reinforced laminates were evaluated to assess the possibility of using it as new material in engineering applications. Samples were fabricated by the hand lay-up process (30:70 fibre and matrix ratio by weight) and the properties evaluated using the INSTRON material testing system. The mechanical properties were tested and showed that glass laminate has the maximum tensile strength of 63 MPa, bending strength of 0.5 MPa, compressive strength of 37.75 MPa and the impact strength of 17.82 J/m 2 . The ukam plant fibre laminate has the maximum tensile strength of 16.25 MPa and the impact strength of 9.8J/m among the natural fibres; the sisal laminate has the maximum compressive strength of 42 MPa and maximum bending strength of 0.0036 MPa among the natural fibres. Results indicated that natural fibres are of interest for low-cost engineering applications and can compete with artificial glass fibres (E-glass fibre) when a high stiffness per unit weight is desirable. Results also indicated that future research towards significant improvements in tensile and impact strength of these types of composites should focus on the optimisation of fibre strength rather than interfacial bond strength.

A forced convection automatic cabinet dryer integrated with a data logger was designed and fabricated. The okra samples were dried in the dryer at drying temperatures of 50, 60, and 70 °C and at three different load densities of 200, 300, and 400 g at a continuous air velocity of 0.7 m·s^–1. Energy and exergy analyses of the drying process were performed. The obtained results showed that the energy efficiency, energy utilisation, and utilisation ratio increased from 26.59 to 68.24%, 5.47 to 114.36 W, and 0.36 to 0.71 as the temperature increased to 70 °C, respectively. The inflow, outflow, and exergy losses were in the range of 7.02 to 26.14 W, 4.43 to 14.16 W, and 2.59 to 11.98 W, respectively, while exergy efficiency varied from 49.15 to 63.47%. The findings show that exergy efficiencies decrease with an increase in the drying temperature, but increase with a lower load rate. The index of sustainability varies from 2.14 to 2.77, the value increases as the load density decreases while it decreases with a temperature increment.

In this study, drying characteristics, kinetic modelling, energy and exergy analyses of a convective hot air dryer are presented for water yam. The drying experiments were carried out at temperature levels of 50, 60, and 70°C and slice thicknesses of 3, 6, and 9 mm. The effects of drying variables on the drying rate (DR), moisture diffusivity (Deff), activation energy (Ea), energy utilization (EU), energy utilization ratio (EUR), exergy loss (EXL), exergy efficiency (EXeff), improvement potential (IP), and exergetic sustainability index (ESI) were investigated. The results showed that increasing air temperature increased the DR, Deff, EU, EUR, EXL, EXeff, IP, and ESI, while increasing the slice thickness increased Deff and Ea, but decreased the DR. The highest Deff and Ea values were 4.2 × 10−8 m2/s, and 53 KJ/mol, respectively. EU and EUR varied from 10 to 150 J/s and 0.39 to 0.79, respectively. EXL and EXeff varied between 2 and 12.5 J/s and 58 to 75 %, respectively. Midilli’s model had the best performance in predicting the moisture ratio of water yam with coefficient of determination (R2 = 0.9998), root mean square error (RMSE = 0.0049), and sum of square error (SSE = 0.0023).

Experimental studies of some properties influencing cracking and separation of palm kernel from the shell was conducted in a palm kernel dual processing machine. A mechanical cracking cum separating machine was developed for the study. The cracking unit consists of feed hopper, impeller shaft, cracking drum and impeller blade. The nut falls by gravity through the hopper channel into the cracking drum where the cracking process takes place through the help of impeller blades that flip the palm nut against the walls of cylindrical cracking drum. The mass of cracked nut flows through the separating unit that separates the kernel from the shell. The separation is induced by high current of air mass generated by an axial fan. A dura palm variety was selected and a total sample of eighteen thousand (18000) palm nuts were obtained and divided into two groups (feed rates), A and B, of eight thousand and ten thousand palm nuts respectively. Sample groups A and B were further divided into five sub -groups of four hundred (400) and five hundred (500) palm kernel nuts. Each sub group (feed rate) was replicated four times at different shaft speeds (600, 900, 1200, 1500 and 1800 rpm). Results showed that cracking efficiencies increased with respect to speed. Un-cracked nuts percentage ranged from 1.3 to 5.3% at 7.1% moisture content, and 1.6 to 4.5% for 400 and 500 feed rates, respectively. Cracking time for both feed rates decreased with shaft speed. Throughput capacity of 11.49 kg/h was observed to be the lowest at 600 rpm and moisture content of 7.1% for both 400 feed rates and the highest throughput capacity of 37.16 kg/h was recorded at 1800 rpm at moisture contents of 9.3% and 16.1%. The results of this study shows that moisture content, engine speed and feed rate are significant parameters that influence cracking of nuts and separation of palm kernel from the shell.