Abstract:Conventional pin-to-point continuous wave Helium Corona plasma discharge was successfully used in Soft Plasma Polymerization (SPP) processes to immobilize into water and onto glass polymerized bioactive Cerrena unicolor laccase coatings. The coatings were tested for bioactivity and durability under water wash. The coatings showed up to 59% bioactivity relative to the native laccase in water deposition, undoubtedly due to damage to and fragmentation of monomer molecules by the active, energetic species in the plasma. However, plasma deposited laccase coatings on glass delivered 7 times the laccase activity of the same non-plasma deposition process in the coating after water wash. This latter result would seem to be due to the ability of the plasma to both crosslink monomer and more strongly bond it to the glass surface by a combination of surface cleaning and the creation of active, high energy sites in both glass and laccase molecules. FTIR analysis indicated that the core copper containing moieties at the centre of the molecule largely remain undamaged by this plasma type so that bonding and cross-linking reactions are likely to mainly involve species around the outer perimeter of the molecule. The chemical composition and structure of laccase biocoatings deposited by Corona SPP are described. The combination of the coating performance parameter values for retained activity and durability under water wash indicates that a relatively simple Corona plasma process for deposition of biocoatings, which directly polymerizes the monomer with no added matrix or encapsulant material, may offer enhanced solutions for biocatalyst, sensor or lab-on-a-chip applications.

No abstract

Development of new techniques for deposition of biologically active coatings in the form of bio-recognition layers in biosensor construction is a current technological challenge. Biosensors are widely applied in environmental protection in determination of hazardous materials, e.g., catechol, hydrochinon or resorcinol. Application of a soft plasma polymerization (SPP) technique by lowenergy-density corona discharge has allowed significant simplification of the deposition process of bio-recognition layers. However, the mechanism of the SPP process is by no means fully understood. This paper presents insights into the mechanism of binding laccase enzyme onto graphene oxide (GO) and multiwalled carbon nanotubes (MWCNT) through analysis carried out by density functional theory (DFT) methods and Fourier transform infrared spectroscopy (FTIR). The objective was to examine the mechanism on the basis of binding energies and electrostatic interactions between laccase and carbon nanomaterials as well as enzyme structure after cold plasma deposition. The lowest binding energies have been calculated for the ON bond between the arginine amino acid of laccase and the hydroxyl group of GO and the CO bond between the serine molecule of laccase and the carboxyl groups of GO and MWCNT. FTIR and DFT studies showed that the chemical structures of the laccase enzyme and carbon nanomaterials after corona jet plasma treatment are not substantially changed. Preliminary recognition of the mechanism of biosensing layer deposition by the SPP technique opens the way to application of this innovative technique to the construction of other biosensors such as for determination of pollutants in water samples.

No abstract

We present quantum chemical theoretical estimations of the anti-corrosive properties of THAM (tris(hydroxymethyl)aminomethane) and three derivatives that differ in the number of benzene rings: THAM-1 (2-amino-3-hydroxy-2-(hydroxymethyl) propylobenzoate), THAM-2 (2-amino-2-(hydroxymetyl)prapan-1,3-diyldibenzoate) and THAM-3 (2-amino-propan-1,2,3-triyltribenzoate). Fourteen exchange-correlation functionals based on the density functional theory (DFT) were chosen for quantum chemical study of THAM derivatives. The objective was to examine the effect of benzene rings on potential anti-corrosive properties of THAM compounds. The results indicate that the addition of benzene rings in THAM derivatives is likely to significantly enhance electrostatic bonding of a THAM-based coating to a presented metal surface and, thus, its adhesion and long-term effect in corrosion inhibition. Whereas it is clear that all three derivatives appear to be superior in their bonding characteristics to pure THAM, the potential order of merit between the three is less clear, although THAM-3 presents as possibly superior.

Development of new, faster methods of biosensor construction is a huge challenge for current science and industry. In this work, biosensor construction was carried out using a new soft plasma polymerization (SPP) method in which a bio-recognition layer of laccase enzyme was polymerized and bonded to a glassy carbon electrode (GCE) substrate under atmospheric pressure with a corona discharge jet. Laccase belongs to the oxidoreductase enzyme group with four copper atoms in its active center. Application of the corona SPP plasma method allows reduction of the time needed for biosensor construction from several hours to minutes. The presented work includes optimization of the laccase bio-recognition layer deposition time, structural studies of the deposited laccase layer, as well as study of the fabricated biosensor applicability for the determination of Rutin in real pharmaceutical samples. This method produces a biosensor with two linear ranges from 0.3 μmol/dm3 to 0.5 μmol/dm3 and from 0.8 μmol/dm3 to 16 μmol/dm3 of Rutin concentration. Results shown in this work indicate that application of the one-step, corona SPP method enables biosensor construction with comparable analytical parameters to biosensors fabricated by conventional, multi-step, wet methods.

Destructive corrosion processes lead to the loss of primary mechanical properties of metal construction materials, which generates additional costs during their maintenance connected with repairs and protection. The effectiveness of corrosion inhibitors can be determined by using many methods, in particular quantum chemical modeling. The subject of the theoretical analyses presented in this work involves the anticorrosion properties of amines with various chemical structures. Evaluation of the corrosion inhibition properties of selected amines was performed on the basis of the HOMO–LUMO energy gap, dipole moment (µ), electronegativity (χ) determined as a result of the energy of the highest occupied molecular orbital (HOMO) and the energy of the lowest unoccupied molecular orbital (LUMO). Moreover, the HSAB (Hard and Soft Acids and Bases) theory was used to explain the reactivity of the analyzed amines, while the Mulliken population analysis was used to determine their electrostatic interactions with the surface of protected metal. The obtained results indicate that the protonation reaction of aliphatic amines leads to a change in the nature of the formation of a coordination bond with the surface of the protected metal. In turn, the quantum chemical calculations showed that the protonation reaction of aliphatic amines leads to a decrease in their corrosion inhibition efficiency. Most of the analyzed parameters indicated that tertiary amines are characterized by the highest corrosion inhibition efficiency.

No abstract